Chapter 8. The Point-to-Point Protocol

Table of Contents
8.1. PPP on Linux
8.2. Running pppd
8.3. Using Options Files
8.4. Using chat to Automate Dialing
8.5. IP Configuration Options
8.5.1. Choosing IP Addresses
8.5.2. Routing Through a PPP Link
8.6. Link Control Options
8.7. General Security Considerations
8.8. Authentication with PPP
8.8.1. PAP Versus CHAP
8.8.2. The CHAP Secrets File
8.8.3. The PAP Secrets File
8.9. Debugging Your PPP Setup
8.10. More Advanced PPP Configurations
8.10.1. PPP Server
8.10.2. Demand Dialing
8.10.3. Persistent Dialing

Like SLIP, PPP is a protocol used to send datagrams across a serial connection; however, it addresses a couple of the deficiencies of SLIP. First, it can carry a large number of protocols and is thus not limited to the IP protocol. It provides error detection on the link itself, while SLIP accepts and forwards corrupted datagrams as long as the corruption does not occur in the header. Equally important, it lets the communicating sides negotiate options, such as the IP address and the maximum datagram size at startup time, and provides client authorization. This built-in negotiation allows reliable automation of the connection establishment, while the authentication removes the need for the clumsy user login accounts that SLIP requires. For each of these capabilities, PPP has a separate protocol. In this chapter, we briefly cover these basic building blocks of PPP. This discussion of PPP is far from complete; if you want to know more about PPP, we urge you to read its RFC specification and the dozen or so companion RFCs.[1] There is also a comprehensive O'Reilly book on the topic of Using & Managing PPP, by Andrew Sun.

At the very bottom of PPP is the High-Level Data Link Control (HDLC) protocol, which defines the boundaries around the individual PPP frames and provides a 16-bit checksum.[2] As opposed to the more primitive SLIP encapsulation, a PPP frame is capable of holding packets from protocols other than IP, such as Novell's IPX or Appletalk. PPP achieves this by adding a protocol field to the basic HDLC frame that identifies the type of packet carried by the frame.

The Link Control Protocol, (LCP) is used on top of HDLC to negotiate options pertaining to the data link. For instance, the Maximum Receive Unit (MRU), states the maximum datagram size that one side of the link agrees to receive.

An important step at the configuration stage of a PPP link is client authorization. Although it is not mandatory, it is really a must for dialup lines in order to keep out intruders. Usually the called host (the server) asks the client to authorize itself by proving it knows some secret key. If the caller fails to produce the correct secret, the connection is terminated. With PPP, authorization works both ways; the caller may also ask the server to authenticate itself. These authentication procedures are totally independent of each other. There are two protocols for different types of authorization, which we will discuss further in this chapter: Password Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP).

Each network protocol that is routed across the data link (like IP and AppleTalk) is configured dynamically using a corresponding Network Control Protocol (NCP). To send IP datagrams across the link, both sides running PPP must first negotiate which IP address each of them uses. The control protocol used for this negotiation is the Internet Protocol Control Protocol (IPCP).

Besides sending standard IP datagrams across the link, PPP also supports Van Jacobson header compression of IP datagrams. This technique shrinks the headers of TCP packets to as little as three bytes. It is also used in CSLIP, and is more colloquially referred to as VJ header compression. The use of compression may be negotiated at startup time through IPCP, as well.

Notes

[1]

Relevant RFCs are listed in the Bibiliography at the end of this book.

[2]

In fact, HDLC is a much more general protocol devised by the International Standards Organization (ISO) and is also an essential component of the X.25 specification.

mirror server hosted at Truenetwork, Russian Federation.