Internet Engineering Task Force (IETF) L. Lhotka Request for Comments: 8349 CZ.NIC Obsoletes: 8022 A. Lindem Category: Standards Track Cisco Systems ISSN: 2070-1721 Y. Qu Huawei March 2018 A YANG Data Model for Routing Management (NMDA Version) Abstract This document specifies three YANG modules and one submodule. Together, they form the core routing data model that serves as a framework for configuring and managing a routing subsystem. It is expected that these modules will be augmented by additional YANG modules defining data models for control-plane protocols, route filters, and other functions. The core routing data model provides common building blocks for such extensions -- routes, Routing Information Bases (RIBs), and control-plane protocols. The YANG modules in this document conform to the Network Management Datastore Architecture (NMDA). This document obsoletes RFC 8022. Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc8349. Lhotka, et al. Standards Track [Page 1]
RFC 8349 YANG Routing Management March 2018 Copyright Notice Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Lhotka, et al. Standards Track [Page 2]
RFC 8349 YANG Routing Management March 2018 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology and Notation . . . . . . . . . . . . . . . . . . 4 2.1. Glossary of New Terms . . . . . . . . . . . . . . . . . . 5 2.2. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 6 2.3. Prefixes in Data Node Names . . . . . . . . . . . . . . . 6 3. Objectives . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. The Design of the Core Routing Data Model . . . . . . . . . . 7 4.1. System-Controlled and User-Controlled List Entries . . . 8 5. Basic Building Blocks . . . . . . . . . . . . . . . . . . . . 9 5.1. Routes . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.2. Routing Information Base (RIB) . . . . . . . . . . . . . 10 5.3. Control-Plane Protocol . . . . . . . . . . . . . . . . . 11 5.3.1. Routing Pseudo-Protocols . . . . . . . . . . . . . . 11 5.3.2. Defining New Control-Plane Protocols . . . . . . . . 11 5.4. Parameters of IPv6 Router Advertisements . . . . . . . . 12 6. Interactions with Other YANG Modules . . . . . . . . . . . . 13 6.1. Module "ietf-interfaces" . . . . . . . . . . . . . . . . 13 6.2. Module "ietf-ip" . . . . . . . . . . . . . . . . . . . . 14 7. Routing Management YANG Module . . . . . . . . . . . . . . . 15 8. IPv4 Unicast Routing Management YANG Module . . . . . . . . . 29 9. IPv6 Unicast Routing Management YANG Module . . . . . . . . . 37 9.1. IPv6 Router Advertisements Submodule . . . . . . . . . . 45 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 56 11. Security Considerations . . . . . . . . . . . . . . . . . . . 57 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 58 12.1. Normative References . . . . . . . . . . . . . . . . . . 58 12.2. Informative References . . . . . . . . . . . . . . . . . 60 Appendix A. The Complete Schema Tree . . . . . . . . . . . . . . 61 Appendix B. Minimum Implementation . . . . . . . . . . . . . . . 66 Appendix C. Example: Adding a New Control-Plane Protocol . . . . 67 Appendix D. Data Tree Example . . . . . . . . . . . . . . . . . 70 Appendix E. NETCONF Get Data Reply Example . . . . . . . . . . . 77 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 80 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 80 Lhotka, et al. Standards Track [Page 3]
RFC 8349 YANG Routing Management March 2018 1. Introduction This document specifies the following YANG modules: o The "ietf-routing" module provides generic components of a routing data model. o The "ietf-ipv4-unicast-routing" module augments the "ietf-routing" module with additional data specific to IPv4 unicast. o The "ietf-ipv6-unicast-routing" module augments the "ietf-routing" module with additional data specific to IPv6 unicast. Its submodule, "ietf-ipv6-router-advertisements", also augments the "ietf-interfaces" [RFC8343] and "ietf-ip" [RFC8344] modules with IPv6 router configuration variables required by [RFC4861]. These modules together define the core routing data model, which is intended as a basis for future data model development covering more-sophisticated routing systems. While these three modules can be directly used for simple IP devices with static routing (see Appendix B), their main purpose is to provide essential building blocks for more-complicated data models involving multiple control-plane protocols, multicast routing, additional address families, and advanced functions such as route filtering or policy routing. To this end, it is expected that the core routing data model will be augmented by numerous modules developed by various IETF working groups. The YANG modules in this document conform to the Network Management Datastore Architecture (NMDA) [RFC8342]. This document obsoletes RFC 8022 [RFC8022]. 2. Terminology and Notation The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. The following terms are defined in [RFC8342]: o client o server o configuration Lhotka, et al. Standards Track [Page 4]
RFC 8349 YANG Routing Management March 2018 o system state o operational state o intended configuration The following terms are defined in [RFC7950]: o action o augment o container o data model o data node o feature o leaf o list o mandatory node o module o presence container o schema tree o RPC (Remote Procedure Call) operation 2.1. Glossary of New Terms core routing data model: YANG data model comprising "ietf-routing", "ietf-ipv4-unicast-routing", and "ietf-ipv6-unicast-routing" modules. direct route: A route to a directly connected network. Routing Information Base (RIB): An object containing a list of routes, together with other information. See Section 5.2 for details. Lhotka, et al. Standards Track [Page 5]
RFC 8349 YANG Routing Management March 2018 system-controlled entry: An entry in a list in the operational state ("config false") that is created by the system independently of what has been explicitly configured. See Section 4.1 for details. user-controlled entry: An entry in a list in the operational state ("config false") that is created and deleted as a direct consequence of certain configuration changes. See Section 4.1 for details. 2.2. Tree Diagrams Tree diagrams used in this document follow the notation defined in [RFC8340]. 2.3. Prefixes in Data Node Names In this document, names of data nodes, actions, and other data model objects are often used without a prefix, as long as it is clear from the context in which YANG module each name is defined. Otherwise, names are prefixed using the standard prefix associated with the corresponding YANG module, as shown in Table 1. +--------+---------------------------+-----------+ | Prefix | YANG module | Reference | +--------+---------------------------+-----------+ | if | ietf-interfaces | [RFC8343] | | ip | ietf-ip | [RFC8344] | | rt | ietf-routing | Section 7 | | v4ur | ietf-ipv4-unicast-routing | Section 8 | | v6ur | ietf-ipv6-unicast-routing | Section 9 | | yang | ietf-yang-types | [RFC6991] | | inet | ietf-inet-types | [RFC6991] | +--------+---------------------------+-----------+ Table 1: Prefixes and Corresponding YANG Modules 3. Objectives The initial design of the core routing data model was driven by the following objectives: o The data model should be suitable for the common address families -- in particular, IPv4 and IPv6 -- and for unicast and multicast routing, as well as Multiprotocol Label Switching (MPLS). o A simple IP routing system, such as one that uses only static routing, should be configurable in a simple way, ideally without any need to develop additional YANG modules. Lhotka, et al. Standards Track [Page 6]
RFC 8349 YANG Routing Management March 2018 o On the other hand, the core routing framework must allow for complicated implementations involving multiple RIBs and multiple control-plane protocols, as well as controlled redistributions of routing information. o Because device vendors will want to map the data models built on this generic framework to their proprietary data models and configuration interfaces, the framework should be flexible enough to facilitate such mapping and accommodate data models with different logic. 4. The Design of the Core Routing Data Model The core routing data model consists of three YANG modules and one submodule. The first module, "ietf-routing", defines the generic components of a routing system. The other two modules -- "ietf-ipv4-unicast-routing" and "ietf-ipv6-unicast-routing" -- augment the "ietf-routing" module with additional data nodes that are needed for IPv4 and IPv6 unicast routing, respectively. The "ietf-ipv6-unicast-routing" module has a submodule, "ietf-ipv6-router-advertisements", that augments the "ietf-interfaces" [RFC8343] and "ietf-ip" [RFC8344] modules with configuration variables for IPv6 Router Advertisements as required by [RFC4861]. Lhotka, et al. Standards Track [Page 7]
RFC 8349 YANG Routing Management March 2018 Figure 1 shows abridged views of the hierarchies. See Appendix A for the complete data trees. +--rw routing +--rw router-id? yang:dotted-quad +--ro interfaces | +--ro interface* if:interface-ref +--rw control-plane-protocols | +--rw control-plane-protocol* [type name] | +--rw type identityref | +--rw name string | +--rw description? string | +--rw static-routes | +--rw v4ur:ipv4 | | ... | +--rw v6ur:ipv6 | ... +--rw ribs +--rw rib* [name] +--rw name string +--rw address-family? identityref +--ro default-rib? boolean {multiple-ribs}? +--ro routes | +--ro route* | ... +---x active-route | +---w input | | +---w v4ur:destination-address? inet:ipv4-address | | +---w v6ur:destination-address? inet:ipv6-address | +--ro output | ... +--rw description? string Figure 1: Data Hierarchy As can be seen from Figure 1, the core routing data model introduces several generic components of a routing framework: routes, RIBs containing lists of routes, and control-plane protocols. Section 5 describes these components in more detail. 4.1. System-Controlled and User-Controlled List Entries The core routing data model defines several lists in the schema tree, such as "rib", that have to be populated with at least one entry in any properly functioning device, and additional entries may be configured by a client. Lhotka, et al. Standards Track [Page 8]
RFC 8349 YANG Routing Management March 2018 In such a list, the server creates the required item as a "system-controlled entry" in the operational state, i.e., inside read-only lists in the "routing" container. An example can be seen in Appendix D: the "/routing/ribs/rib" list has two system-controlled entries -- "ipv4-master" and "ipv6-master". Additional entries called "user-controlled entries" may be created in the configuration by a client, e.g., via the Network Configuration Protocol (NETCONF). If the server accepts a configured user-controlled entry, then this entry also appears in the operational state version of the list. Corresponding entries in both versions of the list (in the intended configuration and the operational state) [RFC8342] have the same value of the list key. A client may also provide supplemental configuration of system- controlled entries. To do so, the client creates a new entry in the configuration with the desired contents. In order to bind this entry to the corresponding entry in the operational state, the key of the configuration entry has to be set to the same value as the key of the operational state entry. Deleting a user-controlled entry from the intended configuration results in the removal of the corresponding entry in the operational state list. In contrast, if a client deletes a system-controlled entry from the intended configuration, only the extra configuration specified in that entry is removed; the corresponding operational state entry is not removed. 5. Basic Building Blocks This section describes the essential components of the core routing data model. 5.1. Routes Routes are basic elements of information in a routing system. The core routing data model defines only the following minimal set of route attributes: o "destination-prefix": address prefix specifying the set of destination addresses for which the route may be used. This attribute is mandatory. Lhotka, et al. Standards Track [Page 9]
RFC 8349 YANG Routing Management March 2018 o "route-preference": an integer value (also known as "administrative distance") that is used for selecting a preferred route among routes with the same destination prefix. A lower value indicates a route that is more preferred. o "next-hop": determines the outgoing interface and/or next-hop address(es), or a special operation to be performed on a packet. Routes are primarily system state and appear as entries in RIBs (Section 5.2), but they may also be found in configuration data -- for example, as manually configured static routes. In the latter case, configurable route attributes are generally a subset of attributes defined for RIB routes. 5.2. Routing Information Base (RIB) Every implementation of the core routing data model manages one or more RIBs. A RIB is a list of routes complemented with administrative data. Each RIB contains only routes of one address family. An address family is represented by an identity derived from the "rt:address-family" base identity. In the core routing data model, RIBs are represented as entries in the list "/routing/ribs/rib" in the operational state. The contents of RIBs are controlled and manipulated by control-plane protocol operations that may result in route additions, removals, and modifications. This also includes manipulations via the "static" and/or "direct" pseudo-protocols; see Section 5.3.1. For every supported address family, exactly one RIB MUST be marked as the "default RIB", in which control-plane protocols place their routes by default. Simple router implementations that do not advertise the "multiple-ribs" feature will typically create one system-controlled RIB per supported address family and mark it as the default RIB. More-complex router implementations advertising the "multiple-ribs" feature support multiple RIBs per address family that can be used for policy routing and other purposes. The following action (see Section 7.15 of [RFC7950]) is defined for the "rib" list: o active-route -- return the active RIB route for the destination address that is specified as the action's input parameter. Lhotka, et al. Standards Track [Page 10]
RFC 8349 YANG Routing Management March 2018 5.3. Control-Plane Protocol The core routing data model provides an open-ended framework for defining multiple control-plane protocol instances, e.g., for Layer 3 routing protocols. Each control-plane protocol instance MUST be assigned a type, which is an identity derived from the "rt:control-plane-protocol" base identity. The core routing data model defines two identities for the "direct" and "static" pseudo-protocols (Section 5.3.1). Multiple control-plane protocol instances of the same type MAY be configured. 5.3.1. Routing Pseudo-Protocols The core routing data model defines two special routing protocol types -- "direct" and "static". Both are in fact pseudo-protocols, which means that they are confined to the local device and do not exchange any routing information with adjacent routers. Every implementation of the core routing data model MUST provide exactly one instance of the "direct" pseudo-protocol type. It is the source of direct routes for all configured address families. Direct routes are normally supplied by the operating system kernel, based on the configuration of network interface addresses; see Section 6.2. A pseudo-protocol of the type "static" allows for specifying routes manually. It MAY be configured in zero or multiple instances, although a typical configuration will have exactly one instance. 5.3.2. Defining New Control-Plane Protocols It is expected that future YANG modules will create data models for additional control-plane protocol types. Such new modules will have to define the protocol-specific data nodes, and they will have to integrate into the core routing framework in the following way: o A new identity MUST be defined for the control-plane protocol, and its base identity MUST be set to "rt:control-plane-protocol" or to an identity derived from "rt:control-plane-protocol". Lhotka, et al. Standards Track [Page 11]
RFC 8349 YANG Routing Management March 2018 o Additional route attributes MAY be defined, preferably in one place by means of defining a YANG grouping. The new attributes have to be inserted by augmenting the definitions of the node /rt:routing/rt:ribs/rt:rib/rt:routes/rt:route and possibly other places in the schema tree. o Data nodes for the new protocol can be defined by augmenting the "control-plane-protocol" data node under "/routing". By using a "when" statement, the augmented data nodes specific to the new protocol SHOULD be made conditional and valid only if the value of "rt:type" or "rt:source-protocol" is equal to (or derived from) the new protocol's identity. It is also RECOMMENDED that protocol-specific data nodes be encapsulated in an appropriately named container with presence. Such a container may contain mandatory data nodes that are otherwise forbidden at the top level of an augment. The above steps are implemented by the example YANG module for the Routing Information Protocol (RIP); see Appendix C. 5.4. Parameters of IPv6 Router Advertisements The YANG module "ietf-ipv6-router-advertisements" (Section 9.1), which is a submodule of the "ietf-ipv6-unicast-routing" module, augments the schema tree of IPv6 interfaces with definitions of the following variables as required by Section 6.2.1 of [RFC4861]: o send-advertisements o max-rtr-adv-interval o min-rtr-adv-interval o managed-flag o other-config-flag o link-mtu o reachable-time o retrans-timer o cur-hop-limit Lhotka, et al. Standards Track [Page 12]
RFC 8349 YANG Routing Management March 2018 o default-lifetime o prefix-list: a list of prefixes to be advertised. The following parameters are associated with each prefix in the list: * valid-lifetime * on-link-flag * preferred-lifetime * autonomous-flag NOTES: 1. The "IsRouter" flag, which is also required by [RFC4861], is implemented in the "ietf-ip" module [RFC8344] (leaf "ip:forwarding"). 2. The Neighbor Discovery specification [RFC4861] allows the implementations to decide whether the "valid-lifetime" and "preferred-lifetime" parameters remain the same in consecutive advertisements or decrement in real time. However, the latter behavior seems problematic because the values might be reset again to the (higher) configured values after a configuration is reloaded. Moreover, no implementation is known to use the decrementing behavior. The "ietf-ipv6-router-advertisements" submodule therefore stipulates the former behavior with constant values. 6. Interactions with Other YANG Modules The semantics of the core routing data model also depends on several configuration parameters that are defined in other YANG modules. 6.1. Module "ietf-interfaces" The following boolean switch is defined in the "ietf-interfaces" YANG module [RFC8343]: /if:interfaces/if:interface/if:enabled If this switch is set to "false" for a network-layer interface, then all routing and forwarding functions MUST be disabled on this interface. Lhotka, et al. Standards Track [Page 13]
RFC 8349 YANG Routing Management March 2018 6.2. Module "ietf-ip" The following boolean switches are defined in the "ietf-ip" YANG module [RFC8344]: /if:interfaces/if:interface/ip:ipv4/ip:enabled If this switch is set to "false" for a network-layer interface, then all IPv4 routing and forwarding functions MUST be disabled on this interface. /if:interfaces/if:interface/ip:ipv4/ip:forwarding If this switch is set to "false" for a network-layer interface, then the forwarding of IPv4 datagrams through this interface MUST be disabled. However, the interface MAY participate in other IPv4 routing functions, such as routing protocols. /if:interfaces/if:interface/ip:ipv6/ip:enabled If this switch is set to "false" for a network-layer interface, then all IPv6 routing and forwarding functions MUST be disabled on this interface. /if:interfaces/if:interface/ip:ipv6/ip:forwarding If this switch is set to "false" for a network-layer interface, then the forwarding of IPv6 datagrams through this interface MUST be disabled. However, the interface MAY participate in other IPv6 routing functions, such as routing protocols. In addition, the "ietf-ip" module allows for configuring IPv4 and IPv6 addresses and network prefixes or masks on network-layer interfaces. Configuration of these parameters on an enabled interface MUST result in an immediate creation of the corresponding direct route. The destination prefix of this route is set according to the configured IP address and network prefix/mask, and the interface is set as the outgoing interface for that route. Lhotka, et al. Standards Track [Page 14]
RFC 8349 YANG Routing Management March 2018 7. Routing Management YANG Module <CODE BEGINS> file "ietf-routing@2018-03-13.yang" module ietf-routing { yang-version "1.1"; namespace "urn:ietf:params:xml:ns:yang:ietf-routing"; prefix "rt"; import ietf-yang-types { prefix "yang"; } import ietf-interfaces { prefix "if"; description "An 'ietf-interfaces' module version that is compatible with the Network Management Datastore Architecture (NMDA) is required."; } organization "IETF NETMOD (Network Modeling) Working Group"; contact "WG Web: <https://datatracker.ietf.org/wg/netmod/> WG List: <mailto:rtgwg@ietf.org> Editor: Ladislav Lhotka <mailto:lhotka@nic.cz> Acee Lindem <mailto:acee@cisco.com> Yingzhen Qu <mailto:yingzhen.qu@huawei.com>"; description "This YANG module defines essential components for the management of a routing subsystem. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2018 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). Lhotka, et al. Standards Track [Page 15]
RFC 8349 YANG Routing Management March 2018 This version of this YANG module is part of RFC 8349; see the RFC itself for full legal notices."; revision 2018-03-13 { description "Network Management Datastore Architecture (NMDA) revision."; reference "RFC 8349: A YANG Data Model for Routing Management (NMDA Version)"; } revision 2016-11-04 { description "Initial revision."; reference "RFC 8022: A YANG Data Model for Routing Management"; } /* Features */ feature multiple-ribs { description "This feature indicates that the server supports user-defined RIBs. Servers that do not advertise this feature SHOULD provide exactly one system-controlled RIB per supported address family and also make it the default RIB. This RIB then appears as an entry in the list '/routing/ribs/rib'."; } feature router-id { description "This feature indicates that the server supports an explicit 32-bit router ID that is used by some routing protocols. Servers that do not advertise this feature set a router ID algorithmically, usually to one of the configured IPv4 addresses. However, this algorithm is implementation specific."; } /* Identities */ identity address-family { description "Base identity from which identities describing address families are derived."; } Lhotka, et al. Standards Track [Page 16]
RFC 8349 YANG Routing Management March 2018 identity ipv4 { base address-family; description "This identity represents an IPv4 address family."; } identity ipv6 { base address-family; description "This identity represents an IPv6 address family."; } identity control-plane-protocol { description "Base identity from which control-plane protocol identities are derived."; } identity routing-protocol { base control-plane-protocol; description "Identity from which Layer 3 routing protocol identities are derived."; } identity direct { base routing-protocol; description "Routing pseudo-protocol that provides routes to directly connected networks."; } identity static { base routing-protocol; description "'Static' routing pseudo-protocol."; } /* Type Definitions */ typedef route-preference { type uint32; description "This type is used for route preferences."; } /* Groupings */ Lhotka, et al. Standards Track [Page 17]
RFC 8349 YANG Routing Management March 2018 grouping address-family { description "This grouping provides a leaf identifying an address family."; leaf address-family { type identityref { base address-family; } mandatory true; description "Address family."; } } grouping router-id { description "This grouping provides a router ID."; leaf router-id { type yang:dotted-quad; description "A 32-bit number in the form of a dotted quad that is used by some routing protocols identifying a router."; reference "RFC 2328: OSPF Version 2"; } } grouping special-next-hop { description "This grouping provides a leaf with an enumeration of special next hops."; leaf special-next-hop { type enumeration { enum blackhole { description "Silently discard the packet."; } enum unreachable { description "Discard the packet and notify the sender with an error message indicating that the destination host is unreachable."; } enum prohibit { description "Discard the packet and notify the sender with an error message indicating that the communication is administratively prohibited."; Lhotka, et al. Standards Track [Page 18]
RFC 8349 YANG Routing Management March 2018 } enum receive { description "The packet will be received by the local system."; } } description "Options for special next hops."; } } grouping next-hop-content { description "Generic parameters of next hops in static routes."; choice next-hop-options { mandatory true; description "Options for next hops in static routes. It is expected that further cases will be added through augments from other modules."; case simple-next-hop { description "This case represents a simple next hop consisting of the next-hop address and/or outgoing interface. Modules for address families MUST augment this case with a leaf containing a next-hop address of that address family."; leaf outgoing-interface { type if:interface-ref; description "Name of the outgoing interface."; } } case special-next-hop { uses special-next-hop; } case next-hop-list { container next-hop-list { description "Container for multiple next hops."; list next-hop { key "index"; description "An entry in a next-hop list. Modules for address families MUST augment this list Lhotka, et al. Standards Track [Page 19]
RFC 8349 YANG Routing Management March 2018 with a leaf containing a next-hop address of that address family."; leaf index { type string; description "A user-specified identifier utilized to uniquely reference the next-hop entry in the next-hop list. The value of this index has no semantic meaning other than for referencing the entry."; } leaf outgoing-interface { type if:interface-ref; description "Name of the outgoing interface."; } } } } } } grouping next-hop-state-content { description "Generic state parameters of next hops."; choice next-hop-options { mandatory true; description "Options for next hops. It is expected that further cases will be added through augments from other modules, e.g., for recursive next hops."; case simple-next-hop { description "This case represents a simple next hop consisting of the next-hop address and/or outgoing interface. Modules for address families MUST augment this case with a leaf containing a next-hop address of that address family."; leaf outgoing-interface { type if:interface-ref; description "Name of the outgoing interface."; } } case special-next-hop { uses special-next-hop; Lhotka, et al. Standards Track [Page 20]
RFC 8349 YANG Routing Management March 2018 } case next-hop-list { container next-hop-list { description "Container for multiple next hops."; list next-hop { description "An entry in a next-hop list. Modules for address families MUST augment this list with a leaf containing a next-hop address of that address family."; leaf outgoing-interface { type if:interface-ref; description "Name of the outgoing interface."; } } } } } } grouping route-metadata { description "Common route metadata."; leaf source-protocol { type identityref { base routing-protocol; } mandatory true; description "Type of the routing protocol from which the route originated."; } leaf active { type empty; description "The presence of this leaf indicates that the route is preferred among all routes in the same RIB that have the same destination prefix."; } leaf last-updated { type yang:date-and-time; description "Timestamp of the last modification of the route. If the route was never modified, it is the time when the route was inserted into the RIB."; Lhotka, et al. Standards Track [Page 21]
RFC 8349 YANG Routing Management March 2018 } } /* Data nodes */ container routing { description "Configuration parameters for the routing subsystem."; uses router-id { if-feature "router-id"; description "Support for the global router ID. Routing protocols that use a router ID can use this parameter or override it with another value."; } container interfaces { config false; description "Network-layer interfaces used for routing."; leaf-list interface { type if:interface-ref; description "Each entry is a reference to the name of a configured network-layer interface."; } } container control-plane-protocols { description "Support for control-plane protocol instances."; list control-plane-protocol { key "type name"; description "Each entry contains a control-plane protocol instance."; leaf type { type identityref { base control-plane-protocol; } description "Type of the control-plane protocol -- an identity derived from the 'control-plane-protocol' base identity."; } leaf name { type string; description "An arbitrary name of the control-plane protocol instance."; } Lhotka, et al. Standards Track [Page 22]
RFC 8349 YANG Routing Management March 2018 leaf description { type string; description "Textual description of the control-plane protocol instance."; } container static-routes { when "derived-from-or-self(../type, 'rt:static')" { description "This container is only valid for the 'static' routing protocol."; } description "Support for the 'static' pseudo-protocol. Address-family-specific modules augment this node with their lists of routes."; } } } container ribs { description "Support for RIBs."; list rib { key "name"; description "Each entry contains a configuration for a RIB identified by the 'name' key. Entries having the same key as a system-controlled entry in the list '/routing/ribs/rib' are used for configuring parameters of that entry. Other entries define additional user-controlled RIBs."; leaf name { type string; description "The name of the RIB. For system-controlled entries, the value of this leaf must be the same as the name of the corresponding entry in the operational state. For user-controlled entries, an arbitrary name can be used."; } uses address-family { description "The address family of the system-controlled RIB."; Lhotka, et al. Standards Track [Page 23]
RFC 8349 YANG Routing Management March 2018 } leaf default-rib { if-feature "multiple-ribs"; type boolean; default "true"; config false; description "This flag has the value of 'true' if and only if the RIB is the default RIB for the given address family. By default, control-plane protocols place their routes in the default RIBs."; } container routes { config false; description "Current contents of the RIB."; list route { description "A RIB route entry. This data node MUST be augmented with information specific to routes of each address family."; leaf route-preference { type route-preference; description "This route attribute, also known as 'administrative distance', allows for selecting the preferred route among routes with the same destination prefix. A smaller value indicates a route that is more preferred."; } container next-hop { description "Route's next-hop attribute."; uses next-hop-state-content; } uses route-metadata; } } action active-route { description "Return the active RIB route that is used for the destination address. Address-family-specific modules MUST augment input parameters with a leaf named 'destination-address'."; output { Lhotka, et al. Standards Track [Page 24]
RFC 8349 YANG Routing Management March 2018 container route { description "The active RIB route for the specified destination. If no route exists in the RIB for the destination address, no output is returned. Address-family-specific modules MUST augment this container with appropriate route contents."; container next-hop { description "Route's next-hop attribute."; uses next-hop-state-content; } uses route-metadata; } } } leaf description { type string; description "Textual description of the RIB."; } } } } /* * The subsequent data nodes are obviated and obsoleted * by the Network Management Datastore Architecture * as described in RFC 8342. */ container routing-state { config false; status obsolete; description "State data of the routing subsystem."; uses router-id { status obsolete; description "Global router ID. It may be either configured or assigned algorithmically by the implementation."; } container interfaces { status obsolete; description Lhotka, et al. Standards Track [Page 25]
RFC 8349 YANG Routing Management March 2018 "Network-layer interfaces used for routing."; leaf-list interface { type if:interface-state-ref; status obsolete; description "Each entry is a reference to the name of a configured network-layer interface."; } } container control-plane-protocols { status obsolete; description "Container for the list of routing protocol instances."; list control-plane-protocol { key "type name"; status obsolete; description "State data of a control-plane protocol instance. An implementation MUST provide exactly one system-controlled instance of the 'direct' pseudo-protocol. Instances of other control-plane protocols MAY be created by configuration."; leaf type { type identityref { base control-plane-protocol; } status obsolete; description "Type of the control-plane protocol."; } leaf name { type string; status obsolete; description "The name of the control-plane protocol instance. For system-controlled instances, this name is persistent, i.e., it SHOULD NOT change across reboots."; } } } container ribs { status obsolete; description "Container for RIBs."; list rib { Lhotka, et al. Standards Track [Page 26]
RFC 8349 YANG Routing Management March 2018 key "name"; min-elements 1; status obsolete; description "Each entry represents a RIB identified by the 'name' key. All routes in a RIB MUST belong to the same address family. An implementation SHOULD provide one system-controlled default RIB for each supported address family."; leaf name { type string; status obsolete; description "The name of the RIB."; } uses address-family { status obsolete; description "The address family of the RIB."; } leaf default-rib { if-feature "multiple-ribs"; type boolean; default "true"; status obsolete; description "This flag has the value of 'true' if and only if the RIB is the default RIB for the given address family. By default, control-plane protocols place their routes in the default RIBs."; } container routes { status obsolete; description "Current contents of the RIB."; list route { status obsolete; description "A RIB route entry. This data node MUST be augmented with information specific to routes of each address family."; leaf route-preference { type route-preference; status obsolete; description "This route attribute, also known as 'administrative Lhotka, et al. Standards Track [Page 27]
RFC 8349 YANG Routing Management March 2018 distance', allows for selecting the preferred route among routes with the same destination prefix. A smaller value indicates a route that is more preferred."; } container next-hop { status obsolete; description "Route's next-hop attribute."; uses next-hop-state-content { status obsolete; description "Route's next-hop attribute operational state."; } } uses route-metadata { status obsolete; description "Route metadata."; } } } action active-route { status obsolete; description "Return the active RIB route that is used for the destination address. Address-family-specific modules MUST augment input parameters with a leaf named 'destination-address'."; output { container route { status obsolete; description "The active RIB route for the specified destination. If no route exists in the RIB for the destination address, no output is returned. Address-family-specific modules MUST augment this container with appropriate route contents."; container next-hop { status obsolete; description "Route's next-hop attribute."; uses next-hop-state-content { status obsolete; Lhotka, et al. Standards Track [Page 28]
RFC 8349 YANG Routing Management March 2018 description "Active route state data."; } } uses route-metadata { status obsolete; description "Active route metadata."; } } } } } } } } <CODE ENDS> 8. IPv4 Unicast Routing Management YANG Module <CODE BEGINS> file "ietf-ipv4-unicast-routing@2018-03-13.yang" module ietf-ipv4-unicast-routing { yang-version "1.1"; namespace "urn:ietf:params:xml:ns:yang:ietf-ipv4-unicast-routing"; prefix "v4ur"; import ietf-routing { prefix "rt"; description "An 'ietf-routing' module version that is compatible with the Network Management Datastore Architecture (NMDA) is required."; } import ietf-inet-types { prefix "inet"; } organization "IETF NETMOD (Network Modeling) Working Group"; contact "WG Web: <https://datatracker.ietf.org/wg/netmod/> WG List: <mailto:rtgwg@ietf.org> Editor: Ladislav Lhotka <mailto:lhotka@nic.cz> Lhotka, et al. Standards Track [Page 29]
RFC 8349 YANG Routing Management March 2018 Acee Lindem <mailto:acee@cisco.com> Yingzhen Qu <mailto:yingzhen.qu@huawei.com>"; description "This YANG module augments the 'ietf-routing' module with basic parameters for IPv4 unicast routing. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2018 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC 8349; see the RFC itself for full legal notices."; revision 2018-03-13 { description "Network Management Datastore Architecture (NMDA) revision."; reference "RFC 8349: A YANG Data Model for Routing Management (NMDA Version)"; } revision 2016-11-04 { description "Initial revision."; reference "RFC 8022: A YANG Data Model for Routing Management"; } /* Identities */ identity ipv4-unicast { base rt:ipv4; description "This identity represents the IPv4 unicast address family."; } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route" { when "derived-from-or-self(../../rt:address-family, " Lhotka, et al. Standards Track [Page 30]
RFC 8349 YANG Routing Management March 2018 + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } description "This leaf augments an IPv4 unicast route."; leaf destination-prefix { type inet:ipv4-prefix; description "IPv4 destination prefix."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } description "Augments the 'simple-next-hop' case in IPv4 unicast routes."; leaf next-hop-address { type inet:ipv4-address; description "IPv4 address of the next hop."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:next-hop-list/" + "rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } description "This leaf augments the 'next-hop-list' case of IPv4 unicast routes."; leaf address { type inet:ipv4-address; description "IPv4 address of the next hop."; } } augment Lhotka, et al. Standards Track [Page 31]
RFC 8349 YANG Routing Management March 2018 "/rt:routing/rt:ribs/rt:rib/rt:active-route/rt:input" { when "derived-from-or-self(../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast RIBs."; } description "This augment adds the input parameter of the 'active-route' action."; leaf destination-address { type inet:ipv4-address; description "IPv4 destination address."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route" { when "derived-from-or-self(../../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } description "This augment adds the destination prefix to the reply of the 'active-route' action."; leaf destination-prefix { type inet:ipv4-prefix; description "IPv4 destination prefix."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } description "Augments the 'simple-next-hop' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv4-address; description "IPv4 address of the next hop."; Lhotka, et al. Standards Track [Page 32]
RFC 8349 YANG Routing Management March 2018 } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:next-hop-list/rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } description "Augments the 'next-hop-list' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv4-address; description "IPv4 address of the next hop."; } } augment "/rt:routing/rt:control-plane-protocols/" + "rt:control-plane-protocol/rt:static-routes" { description "This augment defines the 'static' pseudo-protocol with data specific to IPv4 unicast."; container ipv4 { description "Support for a 'static' pseudo-protocol instance consists of a list of routes."; list route { key "destination-prefix"; description "A list of static routes."; leaf destination-prefix { type inet:ipv4-prefix; mandatory true; description "IPv4 destination prefix."; } leaf description { type string; description "Textual description of the route."; } container next-hop { description "Support for next-hop."; Lhotka, et al. Standards Track [Page 33]
RFC 8349 YANG Routing Management March 2018 uses rt:next-hop-content { augment "next-hop-options/simple-next-hop" { description "Augments the 'simple-next-hop' case in IPv4 static routes."; leaf next-hop-address { type inet:ipv4-address; description "IPv4 address of the next hop."; } } augment "next-hop-options/next-hop-list/next-hop-list/" + "next-hop" { description "Augments the 'next-hop-list' case in IPv4 static routes."; leaf next-hop-address { type inet:ipv4-address; description "IPv4 address of the next hop."; } } } } } } } /* * The subsequent data nodes are obviated and obsoleted * by the Network Management Datastore Architecture * as described in RFC 8342. */ augment "/rt:routing-state/rt:ribs/rt:rib/rt:routes/rt:route" { when "derived-from-or-self(../../rt:address-family, " + "'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } status obsolete; description "This leaf augments an IPv4 unicast route."; leaf destination-prefix { type inet:ipv4-prefix; status obsolete; description "IPv4 destination prefix."; } Lhotka, et al. Standards Track [Page 34]
RFC 8349 YANG Routing Management March 2018 } augment "/rt:routing-state/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:simple-next-hop" { when "derived-from-or-self( ../../../rt:address-family, 'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } status obsolete; description "Augments the 'simple-next-hop' case in IPv4 unicast routes."; leaf next-hop-address { type inet:ipv4-address; status obsolete; description "IPv4 address of the next hop."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:next-hop-list/" + "rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, 'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } status obsolete; description "This leaf augments the 'next-hop-list' case of IPv4 unicast routes."; leaf address { type inet:ipv4-address; status obsolete; description "IPv4 address of the next hop."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:input" { when "derived-from-or-self(../rt:address-family, 'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast RIBs."; } status obsolete; description "This augment adds the input parameter of the 'active-route' action."; Lhotka, et al. Standards Track [Page 35]
RFC 8349 YANG Routing Management March 2018 leaf destination-address { type inet:ipv4-address; status obsolete; description "IPv4 destination address."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route" { when "derived-from-or-self(../../rt:address-family, 'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } status obsolete; description "This augment adds the destination prefix to the reply of the 'active-route' action."; leaf destination-prefix { type inet:ipv4-prefix; status obsolete; description "IPv4 destination prefix."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, 'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } status obsolete; description "Augments the 'simple-next-hop' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv4-address; status obsolete; description "IPv4 address of the next hop."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:next-hop-list/rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, Lhotka, et al. Standards Track [Page 36]
RFC 8349 YANG Routing Management March 2018 'v4ur:ipv4-unicast')" { description "This augment is valid only for IPv4 unicast."; } status obsolete; description "Augments the 'next-hop-list' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv4-address; status obsolete; description "IPv4 address of the next hop."; } } } <CODE ENDS> 9. IPv6 Unicast Routing Management YANG Module <CODE BEGINS> file "ietf-ipv6-unicast-routing@2018-03-13.yang" module ietf-ipv6-unicast-routing { yang-version "1.1"; namespace "urn:ietf:params:xml:ns:yang:ietf-ipv6-unicast-routing"; prefix "v6ur"; import ietf-routing { prefix "rt"; description "An 'ietf-routing' module version that is compatible with the Network Management Datastore Architecture (NMDA) is required."; } import ietf-inet-types { prefix "inet"; description "An 'ietf-interfaces' module version that is compatible with the Network Management Datastore Architecture (NMDA) is required."; } include ietf-ipv6-router-advertisements { revision-date 2018-03-13; } Lhotka, et al. Standards Track [Page 37]
RFC 8349 YANG Routing Management March 2018 organization "IETF NETMOD (Network Modeling) Working Group"; contact "WG Web: <https://datatracker.ietf.org/wg/netmod/> WG List: <mailto:rtgwg@ietf.org> Editor: Ladislav Lhotka <mailto:lhotka@nic.cz> Acee Lindem <mailto:acee@cisco.com> Yingzhen Qu <mailto:yingzhen.qu@huawei.com>"; description "This YANG module augments the 'ietf-routing' module with basic parameters for IPv6 unicast routing. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2018 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC 8349; see the RFC itself for full legal notices."; revision 2018-03-13 { description "Network Management Datastore Architecture (NMDA) revision."; reference "RFC 8349: A YANG Data Model for Routing Management (NMDA Version)"; } /* Identities */ revision 2016-11-04 { description "Initial revision."; reference "RFC 8022: A YANG Data Model for Routing Management"; } Lhotka, et al. Standards Track [Page 38]
RFC 8349 YANG Routing Management March 2018 identity ipv6-unicast { base rt:ipv6; description "This identity represents the IPv6 unicast address family."; } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route" { when "derived-from-or-self(../../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } description "This leaf augments an IPv6 unicast route."; leaf destination-prefix { type inet:ipv6-prefix; description "IPv6 destination prefix."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } description "Augments the 'simple-next-hop' case in IPv6 unicast routes."; leaf next-hop-address { type inet:ipv6-address; description "IPv6 address of the next hop."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:next-hop-list/" + "rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } description "This leaf augments the 'next-hop-list' case of IPv6 unicast routes."; Lhotka, et al. Standards Track [Page 39]
RFC 8349 YANG Routing Management March 2018 leaf address { type inet:ipv6-address; description "IPv6 address of the next hop."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/rt:input" { when "derived-from-or-self(../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast RIBs."; } description "This augment adds the input parameter of the 'active-route' action."; leaf destination-address { type inet:ipv6-address; description "IPv6 destination address."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route" { when "derived-from-or-self(../../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } description "This augment adds the destination prefix to the reply of the 'active-route' action."; leaf destination-prefix { type inet:ipv6-prefix; description "IPv6 destination prefix."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; Lhotka, et al. Standards Track [Page 40]
RFC 8349 YANG Routing Management March 2018 } description "Augments the 'simple-next-hop' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv6-address; description "IPv6 address of the next hop."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:next-hop-list/rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, " + "'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } description "Augments the 'next-hop-list' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv6-address; description "IPv6 address of the next hop."; } } /* Data node augmentations */ augment "/rt:routing/rt:control-plane-protocols/" + "rt:control-plane-protocol/rt:static-routes" { description "This augment defines the 'static' pseudo-protocol with data specific to IPv6 unicast."; container ipv6 { description "Support for a 'static' pseudo-protocol instance consists of a list of routes."; list route { key "destination-prefix"; description "A list of static routes."; leaf destination-prefix { type inet:ipv6-prefix; mandatory true; description Lhotka, et al. Standards Track [Page 41]
RFC 8349 YANG Routing Management March 2018 "IPv6 destination prefix."; } leaf description { type string; description "Textual description of the route."; } container next-hop { description "Next hop for the route."; uses rt:next-hop-content { augment "next-hop-options/simple-next-hop" { description "Augments the 'simple-next-hop' case in IPv6 static routes."; leaf next-hop-address { type inet:ipv6-address; description "IPv6 address of the next hop."; } } augment "next-hop-options/next-hop-list/next-hop-list/" + "next-hop" { description "Augments the 'next-hop-list' case in IPv6 static routes."; leaf next-hop-address { type inet:ipv6-address; description "IPv6 address of the next hop."; } } } } } } } /* * The subsequent data nodes are obviated and obsoleted * by the Network Management Datastore Architecture * as described in RFC 8342. */ augment "/rt:routing-state/rt:ribs/rt:rib/rt:routes/rt:route" { when "derived-from-or-self(../../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; Lhotka, et al. Standards Track [Page 42]
RFC 8349 YANG Routing Management March 2018 } status obsolete; description "This leaf augments an IPv6 unicast route."; leaf destination-prefix { type inet:ipv6-prefix; status obsolete; description "IPv6 destination prefix."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } status obsolete; description "Augments the 'simple-next-hop' case in IPv6 unicast routes."; leaf next-hop-address { type inet:ipv6-address; status obsolete; description "IPv6 address of the next hop."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:routes/rt:route/" + "rt:next-hop/rt:next-hop-options/rt:next-hop-list/" + "rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } status obsolete; description "This leaf augments the 'next-hop-list' case of IPv6 unicast routes."; leaf address { type inet:ipv6-address; status obsolete; description "IPv6 address of the next hop."; } } augment "/rt:routing-state/rt:ribs/rt:rib/" Lhotka, et al. Standards Track [Page 43]
RFC 8349 YANG Routing Management March 2018 + "rt:active-route/rt:input" { when "derived-from-or-self(../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast RIBs."; } status obsolete; description "This augment adds the input parameter of the 'active-route' action."; leaf destination-address { type inet:ipv6-address; status obsolete; description "IPv6 destination address."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route" { when "derived-from-or-self(../../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } status obsolete; description "This augment adds the destination prefix to the reply of the 'active-route' action."; leaf destination-prefix { type inet:ipv6-prefix; status obsolete; description "IPv6 destination prefix."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:simple-next-hop" { when "derived-from-or-self(../../../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } status obsolete; description "Augments the 'simple-next-hop' case in the reply to the 'active-route' action."; leaf next-hop-address { Lhotka, et al. Standards Track [Page 44]
RFC 8349 YANG Routing Management March 2018 type inet:ipv6-address; status obsolete; description "IPv6 address of the next hop."; } } augment "/rt:routing-state/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route/rt:next-hop/rt:next-hop-options/" + "rt:next-hop-list/rt:next-hop-list/rt:next-hop" { when "derived-from-or-self(../../../../../rt:address-family, 'v6ur:ipv6-unicast')" { description "This augment is valid only for IPv6 unicast."; } status obsolete; description "Augments the 'next-hop-list' case in the reply to the 'active-route' action."; leaf next-hop-address { type inet:ipv6-address; status obsolete; description "IPv6 address of the next hop."; } } } <CODE ENDS> 9.1. IPv6 Router Advertisements Submodule <CODE BEGINS> file "ietf-ipv6-router-advertisements@2018-03-13.yang" submodule ietf-ipv6-router-advertisements { yang-version "1.1"; belongs-to ietf-ipv6-unicast-routing { prefix "v6ur"; } import ietf-inet-types { prefix "inet"; } import ietf-interfaces { prefix "if"; description "An 'ietf-interfaces' module version that is compatible with Lhotka, et al. Standards Track [Page 45]
RFC 8349 YANG Routing Management March 2018 the Network Management Datastore Architecture (NMDA) is required."; } import ietf-ip { prefix "ip"; description "An 'ietf-ip' module version that is compatible with the Network Management Datastore Architecture (NMDA) is required."; } organization "IETF NETMOD (Network Modeling) Working Group"; contact "WG Web: <https://datatracker.ietf.org/wg/netmod/> WG List: <mailto:rtgwg@ietf.org> Editor: Ladislav Lhotka <mailto:lhotka@nic.cz> Acee Lindem <mailto:acee@cisco.com> Yingzhen Qu <mailto:yingzhen.qu@huawei.com>"; description "This YANG module augments the 'ietf-ip' module with parameters for IPv6 Router Advertisements. The model fully conforms to the Network Management Datastore Architecture (NMDA). Copyright (c) 2018 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC 8349; see the RFC itself for full legal notices."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6)"; revision 2018-03-13 { Lhotka, et al. Standards Track [Page 46]
RFC 8349 YANG Routing Management March 2018 description "Network Management Datastore Architecture (NMDA) revision."; reference "RFC 8349: A YANG Data Model for Routing Management (NMDA Version)"; } revision 2016-11-04 { description "Initial revision."; reference "RFC 8022: A YANG Data Model for Routing Management"; } augment "/if:interfaces/if:interface/ip:ipv6" { description "Augments interface configuration with parameters of IPv6 Router Advertisements."; container ipv6-router-advertisements { description "Support for IPv6 Router Advertisements."; leaf send-advertisements { type boolean; default "false"; description "A flag indicating whether or not the router sends periodic Router Advertisements and responds to Router Solicitations."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvSendAdvertisements"; } leaf max-rtr-adv-interval { type uint16 { range "4..65535"; } units "seconds"; default "600"; description "The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - MaxRtrAdvInterval"; } leaf min-rtr-adv-interval { type uint16 { range "3..1350"; Lhotka, et al. Standards Track [Page 47]
RFC 8349 YANG Routing Management March 2018 } units "seconds"; must ". <= 0.75 * ../max-rtr-adv-interval" { description "The value MUST NOT be greater than 75% of 'max-rtr-adv-interval'."; } description "The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The default value to be used operationally if this leaf is not configured is determined as follows: - if max-rtr-adv-interval >= 9 seconds, the default value is 0.33 * max-rtr-adv-interval; - otherwise, it is 0.75 * max-rtr-adv-interval."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - MinRtrAdvInterval"; } leaf managed-flag { type boolean; default "false"; description "The value to be placed in the 'Managed address configuration' flag field in the Router Advertisement."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvManagedFlag"; } leaf other-config-flag { type boolean; default "false"; description "The value to be placed in the 'Other configuration' flag field in the Router Advertisement."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvOtherConfigFlag"; } leaf link-mtu { type uint32; default "0"; description "The value to be placed in MTU options sent by the Lhotka, et al. Standards Track [Page 48]
RFC 8349 YANG Routing Management March 2018 router. A value of zero indicates that no MTU options are sent."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvLinkMTU"; } leaf reachable-time { type uint32 { range "0..3600000"; } units "milliseconds"; default "0"; description "The value to be placed in the Reachable Time field in the Router Advertisement messages sent by the router. A value of zero means unspecified (by this router)."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvReachableTime"; } leaf retrans-timer { type uint32; units "milliseconds"; default "0"; description "The value to be placed in the Retrans Timer field in the Router Advertisement messages sent by the router. A value of zero means unspecified (by this router)."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvRetransTimer"; } leaf cur-hop-limit { type uint8; description "The value to be placed in the Cur Hop Limit field in the Router Advertisement messages sent by the router. A value of zero means unspecified (by this router). If this parameter is not configured, the device SHOULD use the IANA-specified value for the default IPv4 Time to Live (TTL) parameter that was in effect at the time of implementation."; reference "RFC 3232: Assigned Numbers: RFC 1700 is Replaced by an On-line Database RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvCurHopLimit Lhotka, et al. Standards Track [Page 49]
RFC 8349 YANG Routing Management March 2018 IANA: IP Parameters (https://www.iana.org/assignments/ip-parameters)"; } leaf default-lifetime { type uint16 { range "0..65535"; } units "seconds"; description "The value to be placed in the Router Lifetime field of Router Advertisements sent from the interface, in seconds. It MUST be either zero or between max-rtr-adv-interval and 9000 seconds. A value of zero indicates that the router is not to be used as a default router. These limits may be overridden by specific documents that describe how IPv6 operates over different link layers. If this parameter is not configured, the device SHOULD use a value of 3 * max-rtr-adv-interval."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvDefaultLifetime"; } container prefix-list { description "Support for prefixes to be placed in Prefix Information options in Router Advertisement messages sent from the interface. Prefixes that are advertised by default but do not have their entries in the child 'prefix' list are advertised with the default values of all parameters. The link-local prefix SHOULD NOT be included in the list of advertised prefixes."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvPrefixList"; list prefix { key "prefix-spec"; description "Support for an advertised prefix entry."; leaf prefix-spec { type inet:ipv6-prefix; description "IPv6 address prefix."; } Lhotka, et al. Standards Track [Page 50]
RFC 8349 YANG Routing Management March 2018 choice control-adv-prefixes { default "advertise"; description "Either (1) the prefix is explicitly removed from the set of advertised prefixes or (2) the parameters with which the prefix is advertised are specified (default case)."; leaf no-advertise { type empty; description "The prefix will not be advertised. This can be used for removing the prefix from the default set of advertised prefixes."; } case advertise { leaf valid-lifetime { type uint32; units "seconds"; default "2592000"; description "The value to be placed in the Valid Lifetime in the Prefix Information option. The designated value of all 1's (0xffffffff) represents infinity."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvValidLifetime"; } leaf on-link-flag { type boolean; default "true"; description "The value to be placed in the on-link flag ('L-bit') field in the Prefix Information option."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvOnLinkFlag"; } leaf preferred-lifetime { type uint32; units "seconds"; must ". <= ../valid-lifetime" { description "This value MUST NOT be greater than valid-lifetime."; } Lhotka, et al. Standards Track [Page 51]
RFC 8349 YANG Routing Management March 2018 default "604800"; description "The value to be placed in the Preferred Lifetime in the Prefix Information option. The designated value of all 1's (0xffffffff) represents infinity."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvPreferredLifetime"; } leaf autonomous-flag { type boolean; default "true"; description "The value to be placed in the Autonomous Flag field in the Prefix Information option."; reference "RFC 4861: Neighbor Discovery for IP version 6 (IPv6) - AdvAutonomousFlag"; } } } } } } } /* * The subsequent data nodes are obviated and obsoleted * by the Network Management Datastore Architecture * as described in RFC 8342. */ augment "/if:interfaces-state/if:interface/ip:ipv6" { status obsolete; description "Augments interface state data with parameters of IPv6 Router Advertisements."; container ipv6-router-advertisements { status obsolete; description "Parameters of IPv6 Router Advertisements."; leaf send-advertisements { type boolean; status obsolete; description "A flag indicating whether or not the router sends periodic Router Advertisements and responds to Router Solicitations."; Lhotka, et al. Standards Track [Page 52]
RFC 8349 YANG Routing Management March 2018 } leaf max-rtr-adv-interval { type uint16 { range "4..1800"; } units "seconds"; status obsolete; description "The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface."; } leaf min-rtr-adv-interval { type uint16 { range "3..1350"; } units "seconds"; status obsolete; description "The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface."; } leaf managed-flag { type boolean; status obsolete; description "The value that is placed in the 'Managed address configuration' flag field in the Router Advertisement."; } leaf other-config-flag { type boolean; status obsolete; description "The value that is placed in the 'Other configuration' flag field in the Router Advertisement."; } leaf link-mtu { type uint32; status obsolete; description "The value that is placed in MTU options sent by the router. A value of zero indicates that no MTU options are sent."; } leaf reachable-time { type uint32 { range "0..3600000"; } units "milliseconds"; Lhotka, et al. Standards Track [Page 53]
RFC 8349 YANG Routing Management March 2018 status obsolete; description "The value that is placed in the Reachable Time field in the Router Advertisement messages sent by the router. A value of zero means unspecified (by this router)."; } leaf retrans-timer { type uint32; units "milliseconds"; status obsolete; description "The value that is placed in the Retrans Timer field in the Router Advertisement messages sent by the router. A value of zero means unspecified (by this router)."; } leaf cur-hop-limit { type uint8; status obsolete; description "The value that is placed in the Cur Hop Limit field in the Router Advertisement messages sent by the router. A value of zero means unspecified (by this router)."; } leaf default-lifetime { type uint16 { range "0..9000"; } units "seconds"; status obsolete; description "The value that is placed in the Router Lifetime field of Router Advertisements sent from the interface, in seconds. A value of zero indicates that the router is not to be used as a default router."; } container prefix-list { status obsolete; description "A list of prefixes that are placed in Prefix Information options in Router Advertisement messages sent from the interface. By default, these are all prefixes that the router advertises via routing protocols as being on-link for the interface from which the advertisement is sent."; list prefix { key "prefix-spec"; status obsolete; Lhotka, et al. Standards Track [Page 54]
RFC 8349 YANG Routing Management March 2018 description "Advertised prefix entry and its parameters."; leaf prefix-spec { type inet:ipv6-prefix; status obsolete; description "IPv6 address prefix."; } leaf valid-lifetime { type uint32; units "seconds"; status obsolete; description "The value that is placed in the Valid Lifetime in the Prefix Information option. The designated value of all 1's (0xffffffff) represents infinity. An implementation SHOULD keep this value constant in consecutive advertisements, except when it is explicitly changed in configuration."; } leaf on-link-flag { type boolean; status obsolete; description "The value that is placed in the on-link flag ('L-bit') field in the Prefix Information option."; } leaf preferred-lifetime { type uint32; units "seconds"; status obsolete; description "The value that is placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of all 1's (0xffffffff) represents infinity. An implementation SHOULD keep this value constant in consecutive advertisements, except when it is explicitly changed in configuration."; } leaf autonomous-flag { type boolean; status obsolete; description "The value that is placed in the Autonomous Flag field in the Prefix Information option."; Lhotka, et al. Standards Track [Page 55]
RFC 8349 YANG Routing Management March 2018 } } } } } } <CODE ENDS> 10. IANA Considerations [RFC8022] registered the following namespace URIs in the "IETF XML Registry" [RFC3688]. IANA has updated the references to refer to this document. URI: urn:ietf:params:xml:ns:yang:ietf-routing Registrant Contact: The IESG. XML: N/A; the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-ipv4-unicast-routing Registrant Contact: The IESG. XML: N/A; the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-ipv6-unicast-routing Registrant Contact: The IESG. XML: N/A; the requested URI is an XML namespace. [RFC8022] registered the following YANG modules in the "YANG Module Names" registry [RFC6020]. IANA has updated (1) the modules per this document and (2) the references to refer to this document. Name: ietf-routing Namespace: urn:ietf:params:xml:ns:yang:ietf-routing Prefix: rt Reference: RFC 8349 Name: ietf-ipv4-unicast-routing Namespace: urn:ietf:params:xml:ns:yang:ietf-ipv4-unicast-routing Prefix: v4ur Reference: RFC 8349 Name: ietf-ipv6-unicast-routing Namespace: urn:ietf:params:xml:ns:yang:ietf-ipv6-unicast-routing Prefix: v6ur Reference: RFC 8349 Lhotka, et al. Standards Track [Page 56]
RFC 8349 YANG Routing Management March 2018 This document registers the following YANG submodule in the "YANG Module Names" registry [RFC6020]: Name: ietf-ipv6-router-advertisements Module: ietf-ipv6-unicast-routing Reference: RFC 8349 11. Security Considerations The YANG modules specified in this document define a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC5246]. The NETCONF access control model [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content. There are a number of data nodes defined in these YANG modules that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability: /routing/control-plane-protocols/control-plane-protocol: This list specifies the control-plane protocols configured on a device. /routing/ribs/rib: This list specifies the RIBs configured for the device. Some of the readable data nodes in these YANG modules may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes. These are the subtrees and data nodes and their sensitivity/vulnerability: /routing/control-plane-protocols/control-plane-protocol: This list specifies the control-plane protocols configured on a device. Refer to the control-plane models for a list of sensitive information. Lhotka, et al. Standards Track [Page 57]
RFC 8349 YANG Routing Management March 2018 /routing/ribs/rib: This list specifies the RIBs and their contents for the device. Access to this information may disclose the network topology and/or other information. Some of the RPC operations in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control access to these operations. These are the operations and their sensitivity/vulnerability: /routing/ribs/rib/active-route: The output from this RPC operation returns the route that is being used for a specified destination. Access to this information may disclose the network topology or relationship (e.g., client/provider). Additionally, the routes used by a network device may be used to mount a subsequent attack on traffic traversing the network device. 12. References 12.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, <https://www.rfc-editor.org/info/rfc2119>. [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004, <https://www.rfc-editor.org/info/rfc3688>. [RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, DOI 10.17487/RFC4861, September 2007, <https://www.rfc-editor.org/info/rfc4861>. [RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2", RFC 5246, DOI 10.17487/RFC5246, August 2008, <https://www.rfc-editor.org/info/rfc5246>. [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010, <https://www.rfc-editor.org/info/rfc6020>. [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, <https://www.rfc-editor.org/info/rfc6241>. Lhotka, et al. Standards Track [Page 58]
RFC 8349 YANG Routing Management March 2018 [RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011, <https://www.rfc-editor.org/info/rfc6242>. [RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013, <https://www.rfc-editor.org/info/rfc6991>. [RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016, <https://www.rfc-editor.org/info/rfc7950>. [RFC8022] Lhotka, L. and A. Lindem, "A YANG Data Model for Routing Management", RFC 8022, DOI 10.17487/RFC8022, November 2016, <https://www.rfc-editor.org/info/rfc8022>. [RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017, <https://www.rfc-editor.org/info/rfc8040>. [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, <https://www.rfc-editor.org/info/rfc8174>. [RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, March 2018, <https://www.rfc-editor.org/info/rfc8341>. [RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018, <https://www.rfc-editor.org/info/rfc8342>. [RFC8343] Bjorklund, M., "A YANG Data Model for Interface Management", RFC 8343, DOI 10.17487/RFC8343, March 2018, <https://www.rfc-editor.org/info/rfc8343>. [RFC8344] Bjorklund, M., "A YANG Data Model for IP Management", RFC 8344, DOI 10.17487/RFC8344, March 2018, <https://www.rfc-editor.org/info/rfc8344>. Lhotka, et al. Standards Track [Page 59]
RFC 8349 YANG Routing Management March 2018 [W3C.REC-xml-20081126] Bray, T., Paoli, J., Sperberg-McQueen, M., Maler, E., and F. Yergeau, "Extensible Markup Language (XML) 1.0 (Fifth Edition)", World Wide Web Consortium Recommendation REC-xml-20081126, November 2008, <https://www.w3.org/TR/2008/REC-xml-20081126>. 12.2. Informative References [RFC7224] Bjorklund, M., "IANA Interface Type YANG Module", RFC 7224, DOI 10.17487/RFC7224, May 2014, <https://www.rfc-editor.org/info/rfc7224>. [RFC7895] Bierman, A., Bjorklund, M., and K. Watsen, "YANG Module Library", RFC 7895, DOI 10.17487/RFC7895, June 2016, <https://www.rfc-editor.org/info/rfc7895>. [RFC7951] Lhotka, L., "JSON Encoding of Data Modeled with YANG", RFC 7951, DOI 10.17487/RFC7951, August 2016, <https://www.rfc-editor.org/info/rfc7951>. [RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018, <https://www.rfc-editor.org/info/rfc8340>. [YANG-Guidelines] Bierman, A., "Guidelines for Authors and Reviewers of YANG Data Model Documents", Work in Progress, draft-ietf-netmod-rfc6087bis-20, March 2018. Lhotka, et al. Standards Track [Page 60]
RFC 8349 YANG Routing Management March 2018 Appendix A. The Complete Schema Tree This appendix presents the complete tree of the core routing data model. See [RFC8340] for an explanation of the symbols used. The data type of every leaf node is shown near the right end of the corresponding line. module: ietf-routing +--rw routing | +--rw router-id? yang:dotted-quad | +--ro interfaces | | +--ro interface* if:interface-ref | +--rw control-plane-protocols | | +--rw control-plane-protocol* [type name] | | +--rw type identityref | | +--rw name string | | +--rw description? string | | +--rw static-routes | | +--rw v4ur:ipv4 | | | +--rw v4ur:route* [destination-prefix] | | | +--rw v4ur:destination-prefix | | | | inet:ipv4-prefix | | | +--rw v4ur:description? string | | | +--rw v4ur:next-hop | | | +--rw (v4ur:next-hop-options) | | | +--:(v4ur:simple-next-hop) | | | | +--rw v4ur:outgoing-interface? | | | | | if:interface-ref | | | | +--rw v4ur:next-hop-address? | | | | inet:ipv4-address | | | +--:(v4ur:special-next-hop) | | | | +--rw v4ur:special-next-hop? | | | | enumeration | | | +--:(v4ur:next-hop-list) | | | +--rw v4ur:next-hop-list | | | +--rw v4ur:next-hop* [index] | | | +--rw v4ur:index | | | | string | | | +--rw v4ur:outgoing-interface? | | | | if:interface-ref | | | +--rw v4ur:next-hop-address? | | | inet:ipv4-address | | +--rw v6ur:ipv6 | | +--rw v6ur:route* [destination-prefix] | | +--rw v6ur:destination-prefix | | | inet:ipv6-prefix | | +--rw v6ur:description? string Lhotka, et al. Standards Track [Page 61]
RFC 8349 YANG Routing Management March 2018 | | +--rw v6ur:next-hop | | +--rw (v6ur:next-hop-options) | | +--:(v6ur:simple-next-hop) | | | +--rw v6ur:outgoing-interface? | | | | if:interface-ref | | | +--rw v6ur:next-hop-address? | | | inet:ipv6-address | | +--:(v6ur:special-next-hop) | | | +--rw v6ur:special-next-hop? | | | enumeration | | +--:(v6ur:next-hop-list) | | +--rw v6ur:next-hop-list | | +--rw v6ur:next-hop* [index] | | +--rw v6ur:index | | | string | | +--rw v6ur:outgoing-interface? | | | if:interface-ref | | +--rw v6ur:next-hop-address? | | inet:ipv6-address | +--rw ribs | +--rw rib* [name] | +--rw name string | +--rw address-family identityref | +--ro default-rib? boolean {multiple-ribs}? | +--ro routes | | +--ro route* | | +--ro route-preference? route-preference | | +--ro next-hop | | | +--ro (next-hop-options) | | | +--:(simple-next-hop) | | | | +--ro outgoing-interface? | | | | | if:interface-ref | | | | +--ro v4ur:next-hop-address? | | | | | inet:ipv4-address | | | | +--ro v6ur:next-hop-address? | | | | inet:ipv6-address | | | +--:(special-next-hop) | | | | +--ro special-next-hop? enumeration | | | +--:(next-hop-list) | | | +--ro next-hop-list | | | +--ro next-hop* | | | +--ro outgoing-interface? | | | | if:interface-ref | | | +--ro v4ur:address? | | | | inet:ipv4-address | | | +--ro v6ur:address? | | | inet:ipv6-address Lhotka, et al. Standards Track [Page 62]
RFC 8349 YANG Routing Management March 2018 | | +--ro source-protocol identityref | | +--ro active? empty | | +--ro last-updated? yang:date-and-time | | +--ro v4ur:destination-prefix? inet:ipv4-prefix | | +--ro v6ur:destination-prefix? inet:ipv6-prefix | +---x active-route | | +---w input | | | +---w v4ur:destination-address? inet:ipv4-address | | | +---w v6ur:destination-address? inet:ipv6-address | | +--ro output | | +--ro route | | +--ro next-hop | | | +--ro (next-hop-options) | | | +--:(simple-next-hop) | | | | +--ro outgoing-interface? | | | | | if:interface-ref | | | | +--ro v4ur:next-hop-address? | | | | | inet:ipv4-address | | | | +--ro v6ur:next-hop-address? | | | | inet:ipv6-address | | | +--:(special-next-hop) | | | | +--ro special-next-hop? | | | | enumeration | | | +--:(next-hop-list) | | | +--ro next-hop-list | | | +--ro next-hop* | | | +--ro outgoing-interface? | | | | if:interface-ref | | | +--ro v4ur:next-hop-address? | | | | inet:ipv4-address | | | +--ro v6ur:next-hop-address? | | | inet:ipv6-address | | +--ro source-protocol identityref | | +--ro active? empty | | +--ro last-updated? | | | yang:date-and-time | | +--ro v4ur:destination-prefix? | | | inet:ipv4-prefix | | +--ro v6ur:destination-prefix? | | inet:ipv6-prefix | +--rw description? string o--ro routing-state o--ro router-id? yang:dotted-quad o--ro interfaces | o--ro interface* if:interface-state-ref Lhotka, et al. Standards Track [Page 63]
RFC 8349 YANG Routing Management March 2018 o--ro control-plane-protocols | o--ro control-plane-protocol* [type name] | o--ro type identityref | o--ro name string o--ro ribs o--ro rib* [name] o--ro name string o--ro address-family identityref o--ro default-rib? boolean {multiple-ribs}? o--ro routes | o--ro route* | o--ro route-preference? route-preference | o--ro next-hop | | o--ro (next-hop-options) | | o--:(simple-next-hop) | | | o--ro outgoing-interface? | | | | if:interface-ref | | | o--ro v4ur:next-hop-address? | | | | inet:ipv4-address | | | o--ro v6ur:next-hop-address? | | | inet:ipv6-address | | o--:(special-next-hop) | | | o--ro special-next-hop? enumeration | | o--:(next-hop-list) | | o--ro next-hop-list | | o--ro next-hop* | | o--ro outgoing-interface? | | | if:interface-ref | | o--ro v4ur:address? | | | inet:ipv4-address | | o--ro v6ur:address? | | inet:ipv6-address | o--ro source-protocol identityref | o--ro active? empty | o--ro last-updated? yang:date-and-time | o--ro v4ur:destination-prefix? inet:ipv4-prefix | o--ro v6ur:destination-prefix? inet:ipv6-prefix o---x active-route o---w input | o---w v4ur:destination-address? inet:ipv4-address | o---w v6ur:destination-address? inet:ipv6-address o--ro output Lhotka, et al. Standards Track [Page 64]
RFC 8349 YANG Routing Management March 2018 o--ro route o--ro next-hop | o--ro (next-hop-options) | o--:(simple-next-hop) | | o--ro outgoing-interface? | | | if:interface-ref | | o--ro v4ur:next-hop-address? | | | inet:ipv4-address | | o--ro v6ur:next-hop-address? | | inet:ipv6-address | o--:(special-next-hop) | | o--ro special-next-hop? | | enumeration | o--:(next-hop-list) | o--ro next-hop-list | o--ro next-hop* | o--ro outgoing-interface? | | if:interface-ref | o--ro v4ur:next-hop-address? | | inet:ipv4-address | o--ro v6ur:next-hop-address? | inet:ipv6-address o--ro source-protocol identityref o--ro active? empty o--ro last-updated? | yang:date-and-time o--ro v4ur:destination-prefix? | inet:ipv4-prefix o--ro v6ur:destination-prefix? inet:ipv6-prefix module: ietf-ipv6-unicast-routing augment /if:interfaces/if:interface/ip:ipv6: +--rw ipv6-router-advertisements +--rw send-advertisements? boolean +--rw max-rtr-adv-interval? uint16 +--rw min-rtr-adv-interval? uint16 +--rw managed-flag? boolean +--rw other-config-flag? boolean +--rw link-mtu? uint32 +--rw reachable-time? uint32 +--rw retrans-timer? uint32 +--rw cur-hop-limit? uint8 +--rw default-lifetime? uint16 +--rw prefix-list +--rw prefix* [prefix-spec] +--rw prefix-spec inet:ipv6-prefix Lhotka, et al. Standards Track [Page 65]
RFC 8349 YANG Routing Management March 2018 +--rw (control-adv-prefixes)? +--:(no-advertise) | +--rw no-advertise? empty +--:(advertise) +--rw valid-lifetime? uint32 +--rw on-link-flag? boolean +--rw preferred-lifetime? uint32 +--rw autonomous-flag? boolean augment /if:interfaces-state/if:interface/ip:ipv6: o--ro ipv6-router-advertisements o--ro send-advertisements? boolean o--ro max-rtr-adv-interval? uint16 o--ro min-rtr-adv-interval? uint16 o--ro managed-flag? boolean o--ro other-config-flag? boolean o--ro link-mtu? uint32 o--ro reachable-time? uint32 o--ro retrans-timer? uint32 o--ro cur-hop-limit? uint8 o--ro default-lifetime? uint16 o--ro prefix-list o--ro prefix* [prefix-spec] o--ro prefix-spec inet:ipv6-prefix o--ro valid-lifetime? uint32 o--ro on-link-flag? boolean o--ro preferred-lifetime? uint32 o--ro autonomous-flag? boolean Appendix B. Minimum Implementation Some parts and options of the core routing model, such as user-defined RIBs, are intended only for advanced routers. This appendix gives basic non-normative guidelines for implementing a bare minimum of available functions. Such an implementation may be used for hosts or very simple routers. A minimum implementation does not support the "multiple-ribs" feature. This means that a single system-controlled RIB is available for each supported address family -- IPv4, IPv6, or both. These RIBs are also the default RIBs. No user-controlled RIBs are allowed. In addition to the mandatory instance of the "direct" pseudo-protocol, a minimum implementation should support configuring instance(s) of the "static" pseudo-protocol. For hosts that are never intended to act as routers, the ability to turn on sending IPv6 Router Advertisements (Section 5.4) should be removed. Lhotka, et al. Standards Track [Page 66]
RFC 8349 YANG Routing Management March 2018 Platforms with severely constrained resources may use deviations for restricting the data model, e.g., limiting the number of "static" control-plane protocol instances. Appendix C. Example: Adding a New Control-Plane Protocol This appendix demonstrates how the core routing data model can be extended to support a new control-plane protocol. The YANG module "example-rip" shown below is intended as an illustration rather than a real definition of a data model for the Routing Information Protocol (RIP). For the sake of brevity, this module does not obey all the guidelines specified in [YANG-Guidelines]. See also Section 5.3.2. module example-rip { yang-version "1.1"; namespace "http://example.com/rip"; prefix "rip"; import ietf-interfaces { prefix "if"; } import ietf-routing { prefix "rt"; } identity rip { base rt:routing-protocol; description "Identity for the Routing Information Protocol (RIP)."; } typedef rip-metric { type uint8 { range "0..16"; } } Lhotka, et al. Standards Track [Page 67]
RFC 8349 YANG Routing Management March 2018 grouping route-content { description "This grouping defines RIP-specific route attributes."; leaf metric { type rip-metric; } leaf tag { type uint16; default "0"; description "This leaf may be used to carry additional information, e.g., an autonomous system (AS) number."; } } augment "/rt:routing/rt:ribs/rt:rib/rt:routes/rt:route" { when "derived-from-or-self(rt:source-protocol, 'rip:rip')" { description "This augment is only valid for a route whose source protocol is RIP."; } description "RIP-specific route attributes."; uses route-content; } augment "/rt:routing/rt:ribs/rt:rib/rt:active-route/" + "rt:output/rt:route" { description "RIP-specific route attributes in the output of an 'active-route' RPC."; uses route-content; } augment "/rt:routing/rt:control-plane-protocols/" + "rt:control-plane-protocol" { when "derived-from-or-self(rt:type,'rip:rip')" { description "This augment is only valid for a routing protocol instance of type 'rip'."; } container rip { presence "RIP configuration"; description "RIP instance configuration."; container interfaces { Lhotka, et al. Standards Track [Page 68]
RFC 8349 YANG Routing Management March 2018 description "Per-interface RIP configuration."; list interface { key "name"; description "RIP is enabled on interfaces that have an entry in this list, unless 'enabled' is set to 'false' for that entry."; leaf name { type if:interface-ref; } leaf enabled { type boolean; default "true"; } leaf metric { type rip-metric; default "1"; } } } leaf update-interval { type uint8 { range "10..60"; } units "seconds"; default "30"; description "Time interval between periodic updates."; } } } } Lhotka, et al. Standards Track [Page 69]
RFC 8349 YANG Routing Management March 2018 Appendix D. Data Tree Example This section contains an example of an instance data tree from the operational state, in JSON encoding [RFC7951]. (This example includes "iana-if-type", which is defined in [RFC7224].) The data conforms to a data model that is defined by the following YANG library specification [RFC7895]: { "ietf-yang-library:modules-state": { "module-set-id": "c2e1f54169aa7f36e1a6e8d0865d441d3600f9c4", "module": [ { "name": "ietf-routing", "revision": "2018-03-13", "feature": [ "multiple-ribs", "router-id" ], "namespace": "urn:ietf:params:xml:ns:yang:ietf-routing", "conformance-type": "implement" }, { "name": "ietf-ipv4-unicast-routing", "revision": "2018-03-13", "namespace": "urn:ietf:params:xml:ns:yang:ietf-ipv4-unicast-routing", "conformance-type": "implement" }, { "name": "ietf-ipv6-unicast-routing", "revision": "2018-03-13", "namespace": "urn:ietf:params:xml:ns:yang:ietf-ipv6-unicast-routing", "conformance-type": "implement", "submodule": [ { "name": "ietf-ipv6-router-advertisements", "revision": "2018-03-13" } ] }, { "name": "ietf-interfaces", "revision": "2018-02-20", "namespace": "urn:ietf:params:xml:ns:yang:ietf-interfaces", "conformance-type": "implement" Lhotka, et al. Standards Track [Page 70]
RFC 8349 YANG Routing Management March 2018 }, { "name": "ietf-inet-types", "namespace": "urn:ietf:params:xml:ns:yang:ietf-inet-types", "revision": "2013-07-15", "conformance-type": "import" }, { "name": "ietf-yang-types", "namespace": "urn:ietf:params:xml:ns:yang:ietf-yang-types", "revision": "2013-07-15", "conformance-type": "import" }, { "name": "iana-if-type", "namespace": "urn:ietf:params:xml:ns:yang:iana-if-type", "revision": "2014-05-08", "conformance-type": "implement" }, { "name": "ietf-ip", "revision": "2018-02-22", "namespace": "urn:ietf:params:xml:ns:yang:ietf-ip", "conformance-type": "implement" } ] } } Lhotka, et al. Standards Track [Page 71]
RFC 8349 YANG Routing Management March 2018 A simple network setup as shown in Figure 2 is assumed: router "A" uses static default routes with the "ISP" router as the next hop. IPv6 Router Advertisements are configured only on the "eth1" interface and disabled on the upstream "eth0" interface. +-----------------+ | | | Router ISP | | | +--------+--------+ |2001:db8:0:1::2 |192.0.2.2 | | |2001:db8:0:1::1 eth0|192.0.2.1 +--------+--------+ | | | Router A | | | +--------+--------+ eth1|198.51.100.1 |2001:db8:0:2::1 | Figure 2: Example of Network Configuration The instance data tree could then be as follows: { "ietf-interfaces:interfaces": { "interface": [ { "name": "eth0", "type": "iana-if-type:ethernetCsmacd", "description": "Uplink to ISP.", "phys-address": "00:0C:42:E5:B1:E9", "oper-status": "up", "statistics": { "discontinuity-time": "2015-10-24T17:11:27+02:00" }, "ietf-ip:ipv4": { "forwarding": true, "mtu": 1500, "address": [ { "ip": "192.0.2.1", "prefix-length": 24 Lhotka, et al. Standards Track [Page 72]
RFC 8349 YANG Routing Management March 2018 } ] }, "ietf-ip:ipv6": { "forwarding": true, "mtu": 1500, "address": [ { "ip": "2001:0db8:0:1::1", "prefix-length": 64 } ], "autoconf": { "create-global-addresses": false }, "ietf-ipv6-unicast-routing:ipv6-router-advertisements": { "send-advertisements": false } } }, { "name": "eth1", "type": "iana-if-type:ethernetCsmacd", "description": "Interface to the internal network.", "phys-address": "00:0C:42:E5:B1:EA", "oper-status": "up", "statistics": { "discontinuity-time": "2015-10-24T17:11:29+02:00" }, "ietf-ip:ipv4": { "forwarding": true, "mtu": 1500, "address": [ { "ip": "198.51.100.1", "prefix-length": 24 } ] }, "ietf-ip:ipv6": { "forwarding": true, "mtu": 1500, "address": [ { "ip": "2001:0db8:0:2::1", "prefix-length": 64 } ], Lhotka, et al. Standards Track [Page 73]
RFC 8349 YANG Routing Management March 2018 "autoconf": { "create-global-addresses": false }, "ietf-ipv6-unicast-routing:ipv6-router-advertisements": { "send-advertisements": true, "prefix-list": { "prefix": [ { "prefix-spec": "2001:db8:0:2::/64" } ] } } } } ] }, "ietf-routing:routing": { "router-id": "192.0.2.1", "control-plane-protocols": { "control-plane-protocol": [ { "type": "ietf-routing:static", "name": "st0", "description": "Static routing is used for the internal network.", "static-routes": { "ietf-ipv4-unicast-routing:ipv4": { "route": [ { "destination-prefix": "0.0.0.0/0", "next-hop": { "next-hop-address": "192.0.2.2" } } ] }, "ietf-ipv6-unicast-routing:ipv6": { "route": [ { "destination-prefix": "::/0", "next-hop": { "next-hop-address": "2001:db8:0:1::2" } } ] } Lhotka, et al. Standards Track [Page 74]
RFC 8349 YANG Routing Management March 2018 } } ] }, "ribs": { "rib": [ { "name": "ipv4-master", "address-family": "ietf-ipv4-unicast-routing:ipv4-unicast", "default-rib": true, "routes": { "route": [ { "ietf-ipv4-unicast-routing:destination-prefix": "192.0.2.1/24", "next-hop": { "outgoing-interface": "eth0" }, "route-preference": 0, "source-protocol": "ietf-routing:direct", "last-updated": "2015-10-24T17:11:27+02:00" }, { "ietf-ipv4-unicast-routing:destination-prefix": "198.51.100.0/24", "next-hop": { "outgoing-interface": "eth1" }, "source-protocol": "ietf-routing:direct", "route-preference": 0, "last-updated": "2015-10-24T17:11:27+02:00" }, { "ietf-ipv4-unicast-routing:destination-prefix": "0.0.0.0/0", "source-protocol": "ietf-routing:static", "route-preference": 5, "next-hop": { "ietf-ipv4-unicast-routing:next-hop-address": "192.0.2.2" }, "last-updated": "2015-10-24T18:02:45+02:00" } ] } }, { Lhotka, et al. Standards Track [Page 75]
RFC 8349 YANG Routing Management March 2018 "name": "ipv6-master", "address-family": "ietf-ipv6-unicast-routing:ipv6-unicast", "default-rib": true, "routes": { "route": [ { "ietf-ipv6-unicast-routing:destination-prefix": "2001:db8:0:1::/64", "next-hop": { "outgoing-interface": "eth0" }, "source-protocol": "ietf-routing:direct", "route-preference": 0, "last-updated": "2015-10-24T17:11:27+02:00" }, { "ietf-ipv6-unicast-routing:destination-prefix": "2001:db8:0:2::/64", "next-hop": { "outgoing-interface": "eth1" }, "source-protocol": "ietf-routing:direct", "route-preference": 0, "last-updated": "2015-10-24T17:11:27+02:00" }, { "ietf-ipv6-unicast-routing:destination-prefix": "::/0", "next-hop": { "ietf-ipv6-unicast-routing:next-hop-address": "2001:db8:0:1::2" }, "source-protocol": "ietf-routing:static", "route-preference": 5, "last-updated": "2015-10-24T18:02:45+02:00" } ] } } ] } } } Lhotka, et al. Standards Track [Page 76]
RFC 8349 YANG Routing Management March 2018 Appendix E. NETCONF Get Data Reply Example This section gives an example of an XML [W3C.REC-xml-20081126] reply to the NETCONF <get-data> request for <operational> for a device that implements the example data models above. <rpc-reply xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" message-id="101"> <data> <routing xmlns="urn:ietf:params:xml:ns:yang:ietf-routing" xmlns:or="urn:ietf:params:xml:ns:yang:ietf-origin"> <router-id or:origin="or:intended">192.0.2.1</router-id> <control-plane-protocols or:origin="or:intended"> <control-plane-protocol> <type>ietf-routing:static</type> <name>static-routing-protocol</name> <static-routes> <ietf-ipv4-unicast-routing:ipv4> <route> <destination-prefix>0.0.0.0/0</destination-prefix> <next-hop> <next-hop-address>192.0.2.2</next-hop-address> </next-hop> </route> </ietf-ipv4-unicast-routing:ipv4> <ietf-ipv6-unicast-routing:ipv6> <route> <destination-prefix>::/0</destination-prefix> <next-hop> <next-hop-address>2001:db8:0:1::2</next-hop-address> </next-hop> </route> </ietf-ipv6-unicast-routing:ipv6> </static-routes> </control-plane-protocol> </control-plane-protocols> <ribs> <rib or:origin="or:intended"> <name>ipv4-master</name> <address-family> ietf-ipv4-unicast-routing:ipv4-unicast </address-family> <default-rib>true</default-rib> <routes> Lhotka, et al. Standards Track [Page 77]
RFC 8349 YANG Routing Management March 2018 <route> <ietf-ipv4-unicast-routing:destination-prefix> 192.0.2.1/24 </ietf-ipv4-unicast-routing:destination-prefix> <next-hop> <outgoing-interface>eth0</outgoing-interface> </next-hop> <route-preference>0</route-preference> <source-protocol>ietf-routing:direct</source-protocol> <last-updated>2015-10-24T17:11:27+02:00</last-updated> </route> <route> <ietf-ipv4-unicast-routing:destination-prefix> 198.51.100.0/24 </ietf-ipv4-unicast-routing:destination-prefix> <next-hop> <outgoing-interface>eth1</outgoing-interface> </next-hop> <route-preference>0</route-preference> <source-protocol>ietf-routing:direct</source-protocol> <last-updated>2015-10-24T17:11:27+02:00</last-updated> </route> <route> <ietf-ipv4-unicast-routing:destination-prefix>0.0.0.0/0 </ietf-ipv4-unicast-routing:destination-prefix> <next-hop> <ietf-ipv4-unicast-routing:next-hop-address>192.0.2.2 </ietf-ipv4-unicast-routing:next-hop-address> </next-hop> <route-preference>5</route-preference> <source-protocol>ietf-routing:static</source-protocol> <last-updated>2015-10-24T18:02:45+02:00</last-updated> </route> </routes> </rib> <rib or:origin="or:intended"> <name>ipv6-master</name> <address-family> ietf-ipv6-unicast-routing:ipv6-unicast </address-family> <default-rib>true</default-rib> <routes> <route> <ietf-ipv6-unicast-routing:destination-prefix> 2001:db8:0:1::/64 </ietf-ipv6-unicast-routing:destination-prefix> <next-hop> <outgoing-interface>eth0</outgoing-interface> Lhotka, et al. Standards Track [Page 78]
RFC 8349 YANG Routing Management March 2018 </next-hop> <route-preference>0</route-preference> <source-protocol>ietf-routing:direct</source-protocol> <last-updated>2015-10-24T17:11:27+02:00</last-updated> </route> <route> <ietf-ipv6-unicast-routing:destination-prefix> 2001:db8:0:2::/64 </ietf-ipv6-unicast-routing:destination-prefix> <next-hop> <outgoing-interface>eth1</outgoing-interface> </next-hop> <route-preference>0</route-preference> <source-protocol>ietf-routing:direct</source-protocol> <last-updated>2015-10-24T17:11:27+02:00</last-updated> </route> <route> <ietf-ipv6-unicast-routing:destination-prefix>::/0 </ietf-ipv6-unicast-routing:destination-prefix> <next-hop> <ietf-ipv6-unicast-routing:next-hop-address> 2001:db8:0:1::2 </ietf-ipv6-unicast-routing:next-hop-address> </next-hop> <route-preference>5</route-preference> <source-protocol>ietf-routing:static</source-protocol> <last-updated>2015-10-24T18:02:45+02:00</last-updated> </route> </routes> </rib> </ribs> </routing> </data> </rpc-reply> Lhotka, et al. Standards Track [Page 79]
RFC 8349 YANG Routing Management March 2018
Acknowledgments
The authors wish to thank Nitin Bahadur, Martin Bjorklund, Dean
Bogdanovic, Joe Clarke, Francis Dupont, Jeff Haas, Joel Halpern,
Wes Hardaker, Jia He, Sriganesh Kini, Suresh Krishnan,
David Lamparter, Xiang Li, Stephane Litkowski, Andrew McGregor,
Jan Medved, Thomas Morin, Tom Petch, Bruno Rijsman,
Juergen Schoenwaelder, Phil Shafer, Dave Thaler, Vladimir Vassilev,
Rob Wilton, Yi Yang, Derek Man-Kit Yeung, and Jeffrey Zhang for their
helpful comments and suggestions.
Authors' Addresses
Ladislav Lhotka
CZ.NIC
Email: lhotka@nic.cz
Acee Lindem
Cisco Systems
Email: acee@cisco.com
Yingzhen Qu
Huawei
2330 Central Expressway
Santa Clara, CA 95050
United States of America
Email: yingzhen.qu@huawei.com
Lhotka, et al. Standards Track [Page 80]
mirror server hosted at Truenetwork, Russian Federation.