Network Working Group R. Housley Request for Comments: 5652 Vigil Security Obsoletes: 3852 September 2009 Category: Standards Track Cryptographic Message Syntax (CMS) Abstract This document describes the Cryptographic Message Syntax (CMS). This syntax is used to digitally sign, digest, authenticate, or encrypt arbitrary message content. Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright and License Notice Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Housley Standards Track [Page 1]
RFC 5652 Cryptographic Message Syntax September 2009 Table of Contents 1. Introduction ....................................................3 1.1. Evolution of the CMS .......................................4 1.1.1. Changes Since PKCS #7 Version 1.5 ...................4 1.1.2. Changes Since RFC 2630 ..............................4 1.1.3. Changes Since RFC 3369 ..............................5 1.1.4. Changes Since RFC 3852 ..............................5 1.2. Terminology ................................................5 1.3. Version Numbers ............................................6 2. General Overview ................................................6 3. General Syntax ..................................................7 4. Data Content Type ...............................................7 5. Signed-data Content Type ........................................8 5.1. SignedData Type ............................................9 5.2. EncapsulatedContentInfo Type ..............................11 5.2.1. Compatibility with PKCS #7 .........................12 5.3. SignerInfo Type ...........................................13 5.4. Message Digest Calculation Process ........................16 5.5. Signature Generation Process ..............................16 5.6. Signature Verification Process ............................17 6. Enveloped-Data Content Type ....................................17 6.1. EnvelopedData Type ........................................18 6.2. RecipientInfo Type ........................................21 6.2.1. KeyTransRecipientInfo Type .........................22 6.2.2. KeyAgreeRecipientInfo Type .........................23 6.2.3. KEKRecipientInfo Type ..............................25 6.2.4. PasswordRecipientInfo Type .........................26 6.2.5. OtherRecipientInfo Type ............................27 6.3. Content-encryption Process ................................27 6.4. Key-Encryption Process ....................................28 7. Digested-Data Content Type .....................................28 8. Encrypted-Data Content Type ....................................29 9. Authenticated-Data Content Type ................................30 9.1. AuthenticatedData Type ....................................31 9.2. MAC Generation ............................................33 9.3. MAC Verification ..........................................34 10. Useful Types ..................................................34 10.1. Algorithm Identifier Types ...............................35 10.1.1. DigestAlgorithmIdentifier .........................35 10.1.2. SignatureAlgorithmIdentifier ......................35 10.1.3. KeyEncryptionAlgorithmIdentifier ..................35 10.1.4. ContentEncryptionAlgorithmIdentifier ..............36 10.1.5. MessageAuthenticationCodeAlgorithm ................36 10.1.6. KeyDerivationAlgorithmIdentifier ..................36 10.2. Other Useful Types .......................................36 10.2.1. RevocationInfoChoices .............................36 10.2.2. CertificateChoices ................................37 Housley Standards Track [Page 2]
RFC 5652 Cryptographic Message Syntax September 2009 10.2.3. CertificateSet ....................................38 10.2.4. IssuerAndSerialNumber .............................38 10.2.5. CMSVersion ........................................39 10.2.6. UserKeyingMaterial ................................39 10.2.7. OtherKeyAttribute .................................39 11. Useful Attributes .............................................39 11.1. Content Type .............................................40 11.2. Message Digest ...........................................40 11.3. Signing Time .............................................41 11.4. Countersignature .........................................42 12. ASN.1 Modules .................................................43 12.1. CMS ASN.1 Module .........................................44 12.2. Version 1 Attribute Certificate ASN.1 Module .............51 13. References ....................................................52 13.1. Normative References .....................................52 13.2. Informative References ...................................53 14. Security Considerations .......................................54 15. Acknowledgments ...............................................56 1. Introduction This document describes the Cryptographic Message Syntax (CMS). This syntax is used to digitally sign, digest, authenticate, or encrypt arbitrary message content. The CMS describes an encapsulation syntax for data protection. It supports digital signatures and encryption. The syntax allows multiple encapsulations; one encapsulation envelope can be nested inside another. Likewise, one party can digitally sign some previously encapsulated data. It also allows arbitrary attributes, such as signing time, to be signed along with the message content, and it provides for other attributes such as countersignatures to be associated with a signature. The CMS can support a variety of architectures for certificate-based key management, such as the one defined by the PKIX (Public Key Infrastructure using X.509) working group [PROFILE]. The CMS values are generated using ASN.1 [X.208-88], using BER- encoding (Basic Encoding Rules) [X.209-88]. Values are typically represented as octet strings. While many systems are capable of transmitting arbitrary octet strings reliably, it is well known that many electronic mail systems are not. This document does not address mechanisms for encoding octet strings for reliable transmission in such environments. Housley Standards Track [Page 3]
RFC 5652 Cryptographic Message Syntax September 2009 1.1. Evolution of the CMS The CMS is derived from PKCS #7 version 1.5, which is documented in RFC 2315 [PKCS#7]. PKCS #7 version 1.5 was developed outside of the IETF; it was originally published as an RSA Laboratories Technical Note in November 1993. Since that time, the IETF has taken responsibility for the development and maintenance of the CMS. Today, several important IETF Standards-Track protocols make use of the CMS. This section describes that changes that the IETF has made to the CMS in each of the published versions. 1.1.1. Changes Since PKCS #7 Version 1.5 RFC 2630 [CMS1] was the first version of the CMS on the IETF Standards Track. Wherever possible, backward compatibility with PKCS #7 version 1.5 is preserved; however, changes were made to accommodate version 1 attribute certificate transfer and to support algorithm-independent key management. PKCS #7 version 1.5 included support only for key transport. RFC 2630 adds support for key agreement and previously distributed symmetric key-encryption key techniques. 1.1.2. Changes Since RFC 2630 RFC 3369 [CMS2] obsoletes RFC 2630 [CMS1] and RFC 3211 [PWRI]. Password-based key management is included in the CMS specification, and an extension mechanism to support new key management schemes without further changes to the CMS is specified. Backward compatibility with RFC 2630 and RFC 3211 is preserved; however, version 2 attribute certificate transfer is added, and the use of version 1 attribute certificates is deprecated. Secure/Multipurpose Internet Mail Extensions (S/MIME) v2 signatures [MSG2], which are based on PKCS #7 version 1.5, are compatible with S/MIME v3 signatures [MSG3]and S/MIME v3.1 signatures [MSG3.1]. However, there are some subtle compatibility issues with signatures based on PKCS #7 version 1.5. These issues are discussed in Section 5.2.1. These issues remain with the current version of the CMS. Specific cryptographic algorithms are not discussed in this document, but they were discussed in RFC 2630. The discussion of specific cryptographic algorithms has been moved to a separate document [CMSALG]. Separation of the protocol and algorithm specifications allows the IETF to update each document independently. This specification does not require the implementation of any particular Housley Standards Track [Page 4]
RFC 5652 Cryptographic Message Syntax September 2009 algorithms. Rather, protocols that rely on the CMS are expected to choose appropriate algorithms for their environment. The algorithms may be selected from [CMSALG] or elsewhere. 1.1.3. Changes Since RFC 3369 RFC 3852 [CMS3] obsoletes RFC 3369 [CMS2]. As discussed in the previous section, RFC 3369 introduced an extension mechanism to support new key management schemes without further changes to the CMS. RFC 3852 introduces a similar extension mechanism to support additional certificate formats and revocation status information formats without further changes to the CMS. These extensions are primarily documented in Sections 10.2.1 and 10.2.2. Backward compatibility with earlier versions of the CMS is preserved. The use of version numbers is described in Section 1.3. Since the publication of RFC 3369, a few errata have been noted. These errata are posted on the RFC Editor web site. These errors have been corrected in this document. The text in Section 11.4 that describes the counter signature unsigned attribute is clarified. Hopefully, the revised text is clearer about the portion of the SignerInfo signature that is covered by a countersignature. 1.1.4. Changes Since RFC 3852 This document obsoletes RFC 3852 [CMS3]. The primary reason for the publication of this document is to advance the CMS along the standards maturity ladder. This document includes the clarifications that were originally published in RFC 4853 [CMSMSIG] regarding the proper handling of the SignedData protected content type when more than one digital signature is present. Since the publication of RFC 3852, a few errata have been noted. These errata are posted on the RFC Editor web site. These errors have been corrected in this document. 1.2. Terminology In this document, the key words MUST, MUST NOT, REQUIRED, SHOULD, SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL are to be interpreted as described in [STDWORDS]. Housley Standards Track [Page 5]
RFC 5652 Cryptographic Message Syntax September 2009 1.3. Version Numbers Each of the major data structures includes a version number as the first item in the data structure. The version numbers are intended to avoid ASN.1 decode errors. Some implementations do not check the version number prior to attempting a decode, and if a decode error occurs, then the version number is checked as part of the error handling routine. This is a reasonable approach; it places error processing outside of the fast path. This approach is also forgiving when an incorrect version number is used by the sender. Most of the initial version numbers were assigned in PKCS #7 version 1.5. Others were assigned when the structure was initially created. Whenever a structure is updated, a higher version number is assigned. However, to ensure maximum interoperability, the higher version number is only used when the new syntax feature is employed. That is, the lowest version number that supports the generated syntax is used. 2. General Overview The CMS is general enough to support many different content types. This document defines one protection content, ContentInfo. ContentInfo encapsulates a single identified content type, and the identified type may provide further encapsulation. This document defines six content types: data, signed-data, enveloped-data, digested-data, encrypted-data, and authenticated-data. Additional content types can be defined outside this document. An implementation that conforms to this specification MUST implement the protection content, ContentInfo, and MUST implement the data, signed-data, and enveloped-data content types. The other content types MAY be implemented. As a general design philosophy, each content type permits single pass processing using indefinite-length Basic Encoding Rules (BER) encoding. Single-pass operation is especially helpful if content is large, stored on tapes, or is "piped" from another process. Single- pass operation has one significant drawback: it is difficult to perform encode operations using the Distinguished Encoding Rules (DER) [X.509-88] encoding in a single pass since the lengths of the various components may not be known in advance. However, signed attributes within the signed-data content type and authenticated attributes within the authenticated-data content type need to be transmitted in DER form to ensure that recipients can verify a content that contains one or more unrecognized attributes. Signed attributes and authenticated attributes are the only data types used in the CMS that require DER encoding. Housley Standards Track [Page 6]
RFC 5652 Cryptographic Message Syntax September 2009 3. General Syntax The following object identifier identifies the content information type: id-ct-contentInfo OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) smime(16) ct(1) 6 } The CMS associates a content type identifier with a content. The syntax MUST have ASN.1 type ContentInfo: ContentInfo ::= SEQUENCE { contentType ContentType, content [0] EXPLICIT ANY DEFINED BY contentType } ContentType ::= OBJECT IDENTIFIER The fields of ContentInfo have the following meanings: contentType indicates the type of the associated content. It is an object identifier; it is a unique string of integers assigned by an authority that defines the content type. content is the associated content. The type of content can be determined uniquely by contentType. Content types for data, signed-data, enveloped-data, digested-data, encrypted-data, and authenticated-data are defined in this document. If additional content types are defined in other documents, the ASN.1 type defined SHOULD NOT be a CHOICE type. 4. Data Content Type The following object identifier identifies the data content type: id-data OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 1 } The data content type is intended to refer to arbitrary octet strings, such as ASCII text files; the interpretation is left to the application. Such strings need not have any internal structure (although they could have their own ASN.1 definition or other structure). S/MIME uses id-data to identify MIME-encoded content. The use of this content identifier is specified in RFC 2311 for S/MIME v2 [MSG2], RFC 2633 for S/MIME v3 [MSG3], and RFC 3851 for S/MIME v3.1 [MSG3.1]. Housley Standards Track [Page 7]
RFC 5652 Cryptographic Message Syntax September 2009 The data content type is generally encapsulated in the signed-data, enveloped-data, digested-data, encrypted-data, or authenticated-data content type. 5. Signed-data Content Type The signed-data content type consists of a content of any type and zero or more signature values. Any number of signers in parallel can sign any type of content. The typical application of the signed-data content type represents one signer's digital signature on content of the data content type. Another typical application disseminates certificates and certificate revocation lists (CRLs). The process by which signed-data is constructed involves the following steps: 1. For each signer, a message digest, or hash value, is computed on the content with a signer-specific message-digest algorithm. If the signer is signing any information other than the content, the message digest of the content and the other information are digested with the signer's message digest algorithm (see Section 5.4), and the result becomes the "message digest." 2. For each signer, the message digest is digitally signed using the signer's private key. 3. For each signer, the signature value and other signer-specific information are collected into a SignerInfo value, as defined in Section 5.3. Certificates and CRLs for each signer, and those not corresponding to any signer, are collected in this step. 4. The message digest algorithms for all the signers and the SignerInfo values for all the signers are collected together with the content into a SignedData value, as defined in Section 5.1. A recipient independently computes the message digest. This message digest and the signer's public key are used to verify the signature value. The signer's public key is referenced in one of two ways. It can be referenced by an issuer distinguished name along with an issuer-specific serial number to uniquely identify the certificate that contains the public key. Alternatively, it can be referenced by a subject key identifier, which accommodates both certified and uncertified public keys. While not required, the signer's certificate can be included in the SignedData certificates field. Housley Standards Track [Page 8]
RFC 5652 Cryptographic Message Syntax September 2009 When more than one signature is present, the successful validation of one signature associated with a given signer is usually treated as a successful signature by that signer. However, there are some application environments where other rules are needed. An application that employs a rule other than one valid signature for each signer must specify those rules. Also, where simple matching of the signer identifier is not sufficient to determine whether the signatures were generated by the same signer, the application specification must describe how to determine which signatures were generated by the same signer. Support of different communities of recipients is the primary reason that signers choose to include more than one signature. For example, the signed-data content type might include signatures generated with the RSA signature algorithm and with the Elliptic Curve Digital Signature Algorithm (ECDSA) signature algorithm. This allows recipients to verify the signature associated with one algorithm or the other. This section is divided into six parts. The first part describes the top-level type SignedData, the second part describes EncapsulatedContentInfo, the third part describes the per-signer information type SignerInfo, and the fourth, fifth, and sixth parts describe the message digest calculation, signature generation, and signature verification processes, respectively. 5.1. SignedData Type The following object identifier identifies the signed-data content type: id-signedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 2 } The signed-data content type shall have ASN.1 type SignedData: SignedData ::= SEQUENCE { version CMSVersion, digestAlgorithms DigestAlgorithmIdentifiers, encapContentInfo EncapsulatedContentInfo, certificates [0] IMPLICIT CertificateSet OPTIONAL, crls [1] IMPLICIT RevocationInfoChoices OPTIONAL, signerInfos SignerInfos } DigestAlgorithmIdentifiers ::= SET OF DigestAlgorithmIdentifier SignerInfos ::= SET OF SignerInfo Housley Standards Track [Page 9]
RFC 5652 Cryptographic Message Syntax September 2009 The fields of type SignedData have the following meanings: version is the syntax version number. The appropriate value depends on certificates, eContentType, and SignerInfo. The version MUST be assigned as follows: IF ((certificates is present) AND (any certificates with a type of other are present)) OR ((crls is present) AND (any crls with a type of other are present)) THEN version MUST be 5 ELSE IF (certificates is present) AND (any version 2 attribute certificates are present) THEN version MUST be 4 ELSE IF ((certificates is present) AND (any version 1 attribute certificates are present)) OR (any SignerInfo structures are version 3) OR (encapContentInfo eContentType is other than id-data) THEN version MUST be 3 ELSE version MUST be 1 digestAlgorithms is a collection of message digest algorithm identifiers. There MAY be any number of elements in the collection, including zero. Each element identifies the message digest algorithm, along with any associated parameters, used by one or more signer. The collection is intended to list the message digest algorithms employed by all of the signers, in any order, to facilitate one-pass signature verification. Implementations MAY fail to validate signatures that use a digest algorithm that is not included in this set. The message digesting process is described in Section 5.4. encapContentInfo is the signed content, consisting of a content type identifier and the content itself. Details of the EncapsulatedContentInfo type are discussed in Section 5.2. certificates is a collection of certificates. It is intended that the set of certificates be sufficient to contain certification paths from a recognized "root" or "top-level certification authority" to all of the signers in the signerInfos field. There may be more certificates than necessary, and there may be certificates sufficient to contain certification paths from two or more independent top-level certification authorities. There may also be fewer certificates than necessary, if it is expected that recipients have an alternate means of obtaining necessary Housley Standards Track [Page 10]
RFC 5652 Cryptographic Message Syntax September 2009 certificates (e.g., from a previous set of certificates). The signer's certificate MAY be included. The use of version 1 attribute certificates is strongly discouraged. crls is a collection of revocation status information. It is intended that the collection contain information sufficient to determine whether the certificates in the certificates field are valid, but such correspondence is not necessary. Certificate revocation lists (CRLs) are the primary source of revocation status information. There MAY be more CRLs than necessary, and there MAY also be fewer CRLs than necessary. signerInfos is a collection of per-signer information. There MAY be any number of elements in the collection, including zero. When the collection represents more than one signature, the successful validation of one of signature from a given signer ought to be treated as a successful signature by that signer. However, there are some application environments where other rules are needed. The details of the SignerInfo type are discussed in Section 5.3. Since each signer can employ a different digital signature technique, and future specifications could update the syntax, all implementations MUST gracefully handle unimplemented versions of SignerInfo. Further, since all implementations will not support every possible signature algorithm, all implementations MUST gracefully handle unimplemented signature algorithms when they are encountered. 5.2. EncapsulatedContentInfo Type The content is represented in the type EncapsulatedContentInfo: EncapsulatedContentInfo ::= SEQUENCE { eContentType ContentType, eContent [0] EXPLICIT OCTET STRING OPTIONAL } ContentType ::= OBJECT IDENTIFIER The fields of type EncapsulatedContentInfo have the following meanings: eContentType is an object identifier. The object identifier uniquely specifies the content type. eContent is the content itself, carried as an octet string. The eContent need not be DER encoded. Housley Standards Track [Page 11]
RFC 5652 Cryptographic Message Syntax September 2009 The optional omission of the eContent within the EncapsulatedContentInfo field makes it possible to construct "external signatures". In the case of external signatures, the content being signed is absent from the EncapsulatedContentInfo value included in the signed-data content type. If the eContent value within EncapsulatedContentInfo is absent, then the signatureValue is calculated and the eContentType is assigned as though the eContent value was present. In the degenerate case where there are no signers, the EncapsulatedContentInfo value being "signed" is irrelevant. In this case, the content type within the EncapsulatedContentInfo value being "signed" MUST be id-data (as defined in Section 4), and the content field of the EncapsulatedContentInfo value MUST be omitted. 5.2.1. Compatibility with PKCS #7 This section contains a word of warning to implementers that wish to support both the CMS and PKCS #7 [PKCS#7] SignedData content types. Both the CMS and PKCS #7 identify the type of the encapsulated content with an object identifier, but the ASN.1 type of the content itself is variable in PKCS #7 SignedData content type. PKCS #7 defines content as: content [0] EXPLICIT ANY DEFINED BY contentType OPTIONAL The CMS defines eContent as: eContent [0] EXPLICIT OCTET STRING OPTIONAL The CMS definition is much easier to use in most applications, and it is compatible with both S/MIME v2 and S/MIME v3. S/MIME signed messages using the CMS and PKCS #7 are compatible because identical signed message formats are specified in RFC 2311 for S/MIME v2 [MSG2], RFC 2633 for S/MIME v3 [MSG3], and RFC 3851 for S/MIME v3.1 [MSG3.1]. S/MIME v2 encapsulates the MIME content in a Data type (that is, an OCTET STRING) carried in the SignedData contentInfo content ANY field, and S/MIME v3 carries the MIME content in the SignedData encapContentInfo eContent OCTET STRING. Therefore, in S/MIME v2, S/MIME v3, and S/MIME v3.1, the MIME content is placed in an OCTET STRING and the message digest is computed over the identical portions of the content. That is, the message digest is computed over the octets comprising the value of the OCTET STRING, neither the tag nor length octets are included. Housley Standards Track [Page 12]
RFC 5652 Cryptographic Message Syntax September 2009 There are incompatibilities between the CMS and PKCS #7 SignedData types when the encapsulated content is not formatted using the Data type. For example, when an RFC 2634 signed receipt [ESS] is encapsulated in the CMS SignedData type, then the Receipt SEQUENCE is encoded in the SignedData encapContentInfo eContent OCTET STRING and the message digest is computed using the entire Receipt SEQUENCE encoding (including tag, length and value octets). However, if an RFC 2634 signed receipt is encapsulated in the PKCS #7 SignedData type, then the Receipt SEQUENCE is DER encoded [X.509-88] in the SignedData contentInfo content ANY field (a SEQUENCE, not an OCTET STRING). Therefore, the message digest is computed using only the value octets of the Receipt SEQUENCE encoding. The following strategy can be used to achieve backward compatibility with PKCS #7 when processing SignedData content types. If the implementation is unable to ASN.1 decode the SignedData type using the CMS SignedData encapContentInfo eContent OCTET STRING syntax, then the implementation MAY attempt to decode the SignedData type using the PKCS #7 SignedData contentInfo content ANY syntax and compute the message digest accordingly. The following strategy can be used to achieve backward compatibility with PKCS #7 when creating a SignedData content type in which the encapsulated content is not formatted using the Data type. Implementations MAY examine the value of the eContentType, and then adjust the expected DER encoding of eContent based on the object identifier value. For example, to support Microsoft Authenticode [MSAC], the following information MAY be included: eContentType Object Identifier is set to { 1 3 6 1 4 1 311 2 1 4 } eContent contains DER-encoded Authenticode signing information 5.3. SignerInfo Type Per-signer information is represented in the type SignerInfo: SignerInfo ::= SEQUENCE { version CMSVersion, sid SignerIdentifier, digestAlgorithm DigestAlgorithmIdentifier, signedAttrs [0] IMPLICIT SignedAttributes OPTIONAL, signatureAlgorithm SignatureAlgorithmIdentifier, signature SignatureValue, unsignedAttrs [1] IMPLICIT UnsignedAttributes OPTIONAL } Housley Standards Track [Page 13]
RFC 5652 Cryptographic Message Syntax September 2009 SignerIdentifier ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, subjectKeyIdentifier [0] SubjectKeyIdentifier } SignedAttributes ::= SET SIZE (1..MAX) OF Attribute UnsignedAttributes ::= SET SIZE (1..MAX) OF Attribute Attribute ::= SEQUENCE { attrType OBJECT IDENTIFIER, attrValues SET OF AttributeValue } AttributeValue ::= ANY SignatureValue ::= OCTET STRING The fields of type SignerInfo have the following meanings: version is the syntax version number. If the SignerIdentifier is the CHOICE issuerAndSerialNumber, then the version MUST be 1. If the SignerIdentifier is subjectKeyIdentifier, then the version MUST be 3. sid specifies the signer's certificate (and thereby the signer's public key). The signer's public key is needed by the recipient to verify the signature. SignerIdentifier provides two alternatives for specifying the signer's public key. The issuerAndSerialNumber alternative identifies the signer's certificate by the issuer's distinguished name and the certificate serial number; the subjectKeyIdentifier identifies the signer's certificate by a key identifier. When an X.509 certificate is referenced, the key identifier matches the X.509 subjectKeyIdentifier extension value. When other certificate formats are referenced, the documents that specify the certificate format and their use with the CMS must include details on matching the key identifier to the appropriate certificate field. Implementations MUST support the reception of the issuerAndSerialNumber and subjectKeyIdentifier forms of SignerIdentifier. When generating a SignerIdentifier, implementations MAY support one of the forms (either issuerAndSerialNumber or subjectKeyIdentifier) and always use it, or implementations MAY arbitrarily mix the two forms. However, subjectKeyIdentifier MUST be used to refer to a public key contained in a non-X.509 certificate. digestAlgorithm identifies the message digest algorithm, and any associated parameters, used by the signer. The message digest is computed on either the content being signed or the content Housley Standards Track [Page 14]
RFC 5652 Cryptographic Message Syntax September 2009 together with the signed attributes using the process described in Section 5.4. The message digest algorithm SHOULD be among those listed in the digestAlgorithms field of the associated SignerData. Implementations MAY fail to validate signatures that use a digest algorithm that is not included in the SignedData digestAlgorithms set. signedAttrs is a collection of attributes that are signed. The field is optional, but it MUST be present if the content type of the EncapsulatedContentInfo value being signed is not id-data. SignedAttributes MUST be DER encoded, even if the rest of the structure is BER encoded. Useful attribute types, such as signing time, are defined in Section 11. If the field is present, it MUST contain, at a minimum, the following two attributes: A content-type attribute having as its value the content type of the EncapsulatedContentInfo value being signed. Section 11.1 defines the content-type attribute. However, the content-type attribute MUST NOT be used as part of a countersignature unsigned attribute as defined in Section 11.4. A message-digest attribute, having as its value the message digest of the content. Section 11.2 defines the message-digest attribute. signatureAlgorithm identifies the signature algorithm, and any associated parameters, used by the signer to generate the digital signature. signature is the result of digital signature generation, using the message digest and the signer's private key. The details of the signature depend on the signature algorithm employed. unsignedAttrs is a collection of attributes that are not signed. The field is optional. Useful attribute types, such as countersignatures, are defined in Section 11. The fields of type SignedAttribute and UnsignedAttribute have the following meanings: attrType indicates the type of attribute. It is an object identifier. attrValues is a set of values that comprise the attribute. The type of each value in the set can be determined uniquely by attrType. The attrType can impose restrictions on the number of items in the set. Housley Standards Track [Page 15]
RFC 5652 Cryptographic Message Syntax September 2009 5.4. Message Digest Calculation Process The message digest calculation process computes a message digest on either the content being signed or the content together with the signed attributes. In either case, the initial input to the message digest calculation process is the "value" of the encapsulated content being signed. Specifically, the initial input is the encapContentInfo eContent OCTET STRING to which the signing process is applied. Only the octets comprising the value of the eContent OCTET STRING are input to the message digest algorithm, not the tag or the length octets. The result of the message digest calculation process depends on whether the signedAttrs field is present. When the field is absent, the result is just the message digest of the content as described above. When the field is present, however, the result is the message digest of the complete DER encoding of the SignedAttrs value contained in the signedAttrs field. Since the SignedAttrs value, when present, must contain the content-type and the message-digest attributes, those values are indirectly included in the result. The content-type attribute MUST NOT be included in a countersignature unsigned attribute as defined in Section 11.4. A separate encoding of the signedAttrs field is performed for message digest calculation. The IMPLICIT [0] tag in the signedAttrs is not used for the DER encoding, rather an EXPLICIT SET OF tag is used. That is, the DER encoding of the EXPLICIT SET OF tag, rather than of the IMPLICIT [0] tag, MUST be included in the message digest calculation along with the length and content octets of the SignedAttributes value. When the signedAttrs field is absent, only the octets comprising the value of the SignedData encapContentInfo eContent OCTET STRING (e.g., the contents of a file) are input to the message digest calculation. This has the advantage that the length of the content being signed need not be known in advance of the signature generation process. Although the encapContentInfo eContent OCTET STRING tag and length octets are not included in the message digest calculation, they are protected by other means. The length octets are protected by the nature of the message digest algorithm since it is computationally infeasible to find any two distinct message contents of any length that have the same message digest. 5.5. Signature Generation Process The input to the signature generation process includes the result of the message digest calculation process and the signer's private key. The details of the signature generation depend on the signature algorithm employed. The object identifier, along with any Housley Standards Track [Page 16]
RFC 5652 Cryptographic Message Syntax September 2009 parameters, that specifies the signature algorithm employed by the signer is carried in the signatureAlgorithm field. The signature value generated by the signer MUST be encoded as an OCTET STRING and carried in the signature field. 5.6. Signature Verification Process The input to the signature verification process includes the result of the message digest calculation process and the signer's public key. The recipient MAY obtain the correct public key for the signer by any means, but the preferred method is from a certificate obtained from the SignedData certificates field. The selection and validation of the signer's public key MAY be based on certification path validation (see [PROFILE]) as well as other external context, but is beyond the scope of this document. The details of the signature verification depend on the signature algorithm employed. The recipient MUST NOT rely on any message digest values computed by the originator. If the SignedData signerInfo includes signedAttributes, then the content message digest MUST be calculated as described in Section 5.4. For the signature to be valid, the message digest value calculated by the recipient MUST be the same as the value of the messageDigest attribute included in the signedAttributes of the SignedData signerInfo. If the SignedData signerInfo includes signedAttributes, then the content-type attribute value MUST match the SignedData encapContentInfo eContentType value. 6. Enveloped-data Content Type The enveloped-data content type consists of an encrypted content of any type and encrypted content-encryption keys for one or more recipients. The combination of the encrypted content and one encrypted content-encryption key for a recipient is a "digital envelope" for that recipient. Any type of content can be enveloped for an arbitrary number of recipients using any of the supported key management techniques for each recipient. The typical application of the enveloped-data content type will represent one or more recipients' digital envelopes on content of the data or signed-data content types. Enveloped-data is constructed by the following steps: 1. A content-encryption key for a particular content-encryption algorithm is generated at random. Housley Standards Track [Page 17]
RFC 5652 Cryptographic Message Syntax September 2009 2. The content-encryption key is encrypted for each recipient. The details of this encryption depend on the key management algorithm used, but four general techniques are supported: key transport: the content-encryption key is encrypted in the recipient's public key; key agreement: the recipient's public key and the sender's private key are used to generate a pairwise symmetric key, then the content-encryption key is encrypted in the pairwise symmetric key; symmetric key-encryption keys: the content-encryption key is encrypted in a previously distributed symmetric key-encryption key; and passwords: the content-encryption key is encrypted in a key- encryption key that is derived from a password or other shared secret value. 3. For each recipient, the encrypted content-encryption key and other recipient-specific information are collected into a RecipientInfo value, defined in Section 6.2. 4. The content is encrypted with the content-encryption key. Content encryption may require that the content be padded to a multiple of some block size; see Section 6.3. 5. The RecipientInfo values for all the recipients are collected together with the encrypted content to form an EnvelopedData value as defined in Section 6.1. A recipient opens the digital envelope by decrypting one of the encrypted content-encryption keys and then decrypting the encrypted content with the recovered content-encryption key. This section is divided into four parts. The first part describes the top-level type EnvelopedData, the second part describes the per- recipient information type RecipientInfo, and the third and fourth parts describe the content-encryption and key-encryption processes. 6.1. EnvelopedData Type The following object identifier identifies the enveloped-data content type: id-envelopedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 3 } Housley Standards Track [Page 18]
RFC 5652 Cryptographic Message Syntax September 2009 The enveloped-data content type shall have ASN.1 type EnvelopedData: EnvelopedData ::= SEQUENCE { version CMSVersion, originatorInfo [0] IMPLICIT OriginatorInfo OPTIONAL, recipientInfos RecipientInfos, encryptedContentInfo EncryptedContentInfo, unprotectedAttrs [1] IMPLICIT UnprotectedAttributes OPTIONAL } OriginatorInfo ::= SEQUENCE { certs [0] IMPLICIT CertificateSet OPTIONAL, crls [1] IMPLICIT RevocationInfoChoices OPTIONAL } RecipientInfos ::= SET SIZE (1..MAX) OF RecipientInfo EncryptedContentInfo ::= SEQUENCE { contentType ContentType, contentEncryptionAlgorithm ContentEncryptionAlgorithmIdentifier, encryptedContent [0] IMPLICIT EncryptedContent OPTIONAL } EncryptedContent ::= OCTET STRING UnprotectedAttributes ::= SET SIZE (1..MAX) OF Attribute The fields of type EnvelopedData have the following meanings: version is the syntax version number. The appropriate value depends on originatorInfo, RecipientInfo, and unprotectedAttrs. The version MUST be assigned as follows: IF (originatorInfo is present) AND ((any certificates with a type of other are present) OR (any crls with a type of other are present)) THEN version is 4 ELSE IF ((originatorInfo is present) AND (any version 2 attribute certificates are present)) OR (any RecipientInfo structures include pwri) OR (any RecipientInfo structures include ori) THEN version is 3 ELSE IF (originatorInfo is absent) AND (unprotectedAttrs is absent) AND (all RecipientInfo structures are version 0) THEN version is 0 ELSE version is 2 Housley Standards Track [Page 19]
RFC 5652 Cryptographic Message Syntax September 2009 originatorInfo optionally provides information about the originator. It is present only if required by the key management algorithm. It may contain certificates and CRLs: certs is a collection of certificates. certs may contain originator certificates associated with several different key management algorithms. certs may also contain attribute certificates associated with the originator. The certificates contained in certs are intended to be sufficient for all recipients to build certification paths from a recognized "root" or "top-level certification authority". However, certs may contain more certificates than necessary, and there may be certificates sufficient to make certification paths from two or more independent top-level certification authorities. Alternatively, certs may contain fewer certificates than necessary, if it is expected that recipients have an alternate means of obtaining necessary certificates (e.g., from a previous set of certificates). crls is a collection of CRLs. It is intended that the set contain information sufficient to determine whether or not the certificates in the certs field are valid, but such correspondence is not necessary. There MAY be more CRLs than necessary, and there MAY also be fewer CRLs than necessary. recipientInfos is a collection of per-recipient information. There MUST be at least one element in the collection. encryptedContentInfo is the encrypted content information. unprotectedAttrs is a collection of attributes that are not encrypted. The field is optional. Useful attribute types are defined in Section 11. The fields of type EncryptedContentInfo have the following meanings: contentType indicates the type of content. contentEncryptionAlgorithm identifies the content-encryption algorithm, and any associated parameters, used to encrypt the content. The content-encryption process is described in Section 6.3. The same content-encryption algorithm and content-encryption key are used for all recipients. encryptedContent is the result of encrypting the content. The field is optional, and if the field is not present, its intended value must be supplied by other means. Housley Standards Track [Page 20]
RFC 5652 Cryptographic Message Syntax September 2009 The recipientInfos field comes before the encryptedContentInfo field so that an EnvelopedData value may be processed in a single pass. 6.2. RecipientInfo Type Per-recipient information is represented in the type RecipientInfo. RecipientInfo has a different format for each of the supported key management techniques. Any of the key management techniques can be used for each recipient of the same encrypted content. In all cases, the encrypted content-encryption key is transferred to one or more recipients. Since all implementations will not support every possible key management algorithm, all implementations MUST gracefully handle unimplemented algorithms when they are encountered. For example, if a recipient receives a content-encryption key encrypted in their RSA public key using RSA-OAEP (Optimal Asymmetric Encryption Padding) and the implementation only supports RSA PKCS #1 v1.5, then a graceful failure must be implemented. Implementations MUST support key transport, key agreement, and previously distributed symmetric key-encryption keys, as represented by ktri, kari, and kekri, respectively. Implementations MAY support the password-based key management as represented by pwri. Implementations MAY support any other key management technique as represented by ori. Since each recipient can employ a different key management technique and future specifications could define additional key management techniques, all implementations MUST gracefully handle unimplemented alternatives within the RecipientInfo CHOICE, all implementations MUST gracefully handle unimplemented versions of otherwise supported alternatives within the RecipientInfo CHOICE, and all implementations MUST gracefully handle unimplemented or unknown ori alternatives. RecipientInfo ::= CHOICE { ktri KeyTransRecipientInfo, kari [1] KeyAgreeRecipientInfo, kekri [2] KEKRecipientInfo, pwri [3] PasswordRecipientinfo, ori [4] OtherRecipientInfo } EncryptedKey ::= OCTET STRING Housley Standards Track [Page 21]
RFC 5652 Cryptographic Message Syntax September 2009 6.2.1. KeyTransRecipientInfo Type Per-recipient information using key transport is represented in the type KeyTransRecipientInfo. Each instance of KeyTransRecipientInfo transfers the content-encryption key to one recipient. KeyTransRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 0 or 2 rid RecipientIdentifier, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, encryptedKey EncryptedKey } RecipientIdentifier ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, subjectKeyIdentifier [0] SubjectKeyIdentifier } The fields of type KeyTransRecipientInfo have the following meanings: version is the syntax version number. If the RecipientIdentifier is the CHOICE issuerAndSerialNumber, then the version MUST be 0. If the RecipientIdentifier is subjectKeyIdentifier, then the version MUST be 2. rid specifies the recipient's certificate or key that was used by the sender to protect the content-encryption key. The content- encryption key is encrypted with the recipient's public key. The RecipientIdentifier provides two alternatives for specifying the recipient's certificate, and thereby the recipient's public key. The recipient's certificate must contain a key transport public key. Therefore, a recipient X.509 version 3 certificate that contains a key usage extension MUST assert the keyEncipherment bit. The issuerAndSerialNumber alternative identifies the recipient's certificate by the issuer's distinguished name and the certificate serial number; the subjectKeyIdentifier identifies the recipient's certificate by a key identifier. When an X.509 certificate is referenced, the key identifier matches the X.509 subjectKeyIdentifier extension value. When other certificate formats are referenced, the documents that specify the certificate format and their use with the CMS must include details on matching the key identifier to the appropriate certificate field. For recipient processing, implementations MUST support both of these alternatives for specifying the recipient's certificate. For sender processing, implementations MUST support at least one of these alternatives. Housley Standards Track [Page 22]
RFC 5652 Cryptographic Message Syntax September 2009 keyEncryptionAlgorithm identifies the key-encryption algorithm, and any associated parameters, used to encrypt the content- encryption key for the recipient. The key-encryption process is described in Section 6.4. encryptedKey is the result of encrypting the content-encryption key for the recipient. 6.2.2. KeyAgreeRecipientInfo Type Recipient information using key agreement is represented in the type KeyAgreeRecipientInfo. Each instance of KeyAgreeRecipientInfo will transfer the content-encryption key to one or more recipients that use the same key agreement algorithm and domain parameters for that algorithm. KeyAgreeRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 3 originator [0] EXPLICIT OriginatorIdentifierOrKey, ukm [1] EXPLICIT UserKeyingMaterial OPTIONAL, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, recipientEncryptedKeys RecipientEncryptedKeys } OriginatorIdentifierOrKey ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, subjectKeyIdentifier [0] SubjectKeyIdentifier, originatorKey [1] OriginatorPublicKey } OriginatorPublicKey ::= SEQUENCE { algorithm AlgorithmIdentifier, publicKey BIT STRING } RecipientEncryptedKeys ::= SEQUENCE OF RecipientEncryptedKey RecipientEncryptedKey ::= SEQUENCE { rid KeyAgreeRecipientIdentifier, encryptedKey EncryptedKey } KeyAgreeRecipientIdentifier ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, rKeyId [0] IMPLICIT RecipientKeyIdentifier } RecipientKeyIdentifier ::= SEQUENCE { subjectKeyIdentifier SubjectKeyIdentifier, date GeneralizedTime OPTIONAL, other OtherKeyAttribute OPTIONAL } SubjectKeyIdentifier ::= OCTET STRING Housley Standards Track [Page 23]
RFC 5652 Cryptographic Message Syntax September 2009 The fields of type KeyAgreeRecipientInfo have the following meanings: version is the syntax version number. It MUST always be 3. originator is a CHOICE with three alternatives specifying the sender's key agreement public key. The sender uses the corresponding private key and the recipient's public key to generate a pairwise key. The content-encryption key is encrypted in the pairwise key. The issuerAndSerialNumber alternative identifies the sender's certificate, and thereby the sender's public key, by the issuer's distinguished name and the certificate serial number. The subjectKeyIdentifier alternative identifies the sender's certificate, and thereby the sender's public key, by a key identifier. When an X.509 certificate is referenced, the key identifier matches the X.509 subjectKeyIdentifier extension value. When other certificate formats are referenced, the documents that specify the certificate format and their use with the CMS must include details on matching the key identifier to the appropriate certificate field. The originatorKey alternative includes the algorithm identifier and sender's key agreement public key. This alternative permits originator anonymity since the public key is not certified. Implementations MUST support all three alternatives for specifying the sender's public key. ukm is optional. With some key agreement algorithms, the sender provides a User Keying Material (UKM) to ensure that a different key is generated each time the same two parties generate a pairwise key. Implementations MUST accept a KeyAgreeRecipientInfo SEQUENCE that includes a ukm field. Implementations that do not support key agreement algorithms that make use of UKMs MUST gracefully handle the presence of UKMs. keyEncryptionAlgorithm identifies the key-encryption algorithm, and any associated parameters, used to encrypt the content- encryption key with the key-encryption key. The key-encryption process is described in Section 6.4. recipientEncryptedKeys includes a recipient identifier and encrypted key for one or more recipients. The KeyAgreeRecipientIdentifier is a CHOICE with two alternatives specifying the recipient's certificate, and thereby the recipient's public key, that was used by the sender to generate a pairwise key-encryption key. The recipient's certificate must contain a key agreement public key. Therefore, a recipient X.509 version 3 certificate that contains a key usage extension MUST assert the keyAgreement bit. The content-encryption key is encrypted in the pairwise key-encryption key. The issuerAndSerialNumber alternative identifies the recipient's Housley Standards Track [Page 24]
RFC 5652 Cryptographic Message Syntax September 2009 certificate by the issuer's distinguished name and the certificate serial number; the RecipientKeyIdentifier is described below. The encryptedKey is the result of encrypting the content-encryption key in the pairwise key-encryption key generated using the key agreement algorithm. Implementations MUST support both alternatives for specifying the recipient's certificate. The fields of type RecipientKeyIdentifier have the following meanings: subjectKeyIdentifier identifies the recipient's certificate by a key identifier. When an X.509 certificate is referenced, the key identifier matches the X.509 subjectKeyIdentifier extension value. When other certificate formats are referenced, the documents that specify the certificate format and their use with the CMS must include details on matching the key identifier to the appropriate certificate field. date is optional. When present, the date specifies which of the recipient's previously distributed UKMs was used by the sender. other is optional. When present, this field contains additional information used by the recipient to locate the public keying material used by the sender. 6.2.3. KEKRecipientInfo Type Recipient information using previously distributed symmetric keys is represented in the type KEKRecipientInfo. Each instance of KEKRecipientInfo will transfer the content-encryption key to one or more recipients who have the previously distributed key-encryption key. KEKRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 4 kekid KEKIdentifier, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, encryptedKey EncryptedKey } KEKIdentifier ::= SEQUENCE { keyIdentifier OCTET STRING, date GeneralizedTime OPTIONAL, other OtherKeyAttribute OPTIONAL } Housley Standards Track [Page 25]
RFC 5652 Cryptographic Message Syntax September 2009 The fields of type KEKRecipientInfo have the following meanings: version is the syntax version number. It MUST always be 4. kekid specifies a symmetric key-encryption key that was previously distributed to the sender and one or more recipients. keyEncryptionAlgorithm identifies the key-encryption algorithm, and any associated parameters, used to encrypt the content- encryption key with the key-encryption key. The key-encryption process is described in Section 6.4. encryptedKey is the result of encrypting the content-encryption key in the key-encryption key. The fields of type KEKIdentifier have the following meanings: keyIdentifier identifies the key-encryption key that was previously distributed to the sender and one or more recipients. date is optional. When present, the date specifies a single key- encryption key from a set that was previously distributed. other is optional. When present, this field contains additional information used by the recipient to determine the key-encryption key used by the sender. 6.2.4. PasswordRecipientInfo Type Recipient information using a password or shared secret value is represented in the type PasswordRecipientInfo. Each instance of PasswordRecipientInfo will transfer the content-encryption key to one or more recipients who possess the password or shared secret value. The PasswordRecipientInfo Type is specified in RFC 3211 [PWRI]. The PasswordRecipientInfo structure is repeated here for completeness. PasswordRecipientInfo ::= SEQUENCE { version CMSVersion, -- Always set to 0 keyDerivationAlgorithm [0] KeyDerivationAlgorithmIdentifier OPTIONAL, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, encryptedKey EncryptedKey } Housley Standards Track [Page 26]
RFC 5652 Cryptographic Message Syntax September 2009 The fields of type PasswordRecipientInfo have the following meanings: version is the syntax version number. It MUST always be 0. keyDerivationAlgorithm identifies the key-derivation algorithm, and any associated parameters, used to derive the key-encryption key from the password or shared secret value. If this field is absent, the key-encryption key is supplied from an external source, for example a hardware crypto token such as a smart card. keyEncryptionAlgorithm identifies the encryption algorithm, and any associated parameters, used to encrypt the content-encryption key with the key-encryption key. encryptedKey is the result of encrypting the content-encryption key with the key-encryption key. 6.2.5. OtherRecipientInfo Type Recipient information for additional key management techniques are represented in the type OtherRecipientInfo. The OtherRecipientInfo type allows key management techniques beyond key transport, key agreement, previously distributed symmetric key-encryption keys, and password-based key management to be specified in future documents. An object identifier uniquely identifies such key management techniques. OtherRecipientInfo ::= SEQUENCE { oriType OBJECT IDENTIFIER, oriValue ANY DEFINED BY oriType } The fields of type OtherRecipientInfo have the following meanings: oriType identifies the key management technique. oriValue contains the protocol data elements needed by a recipient using the identified key management technique. 6.3. Content-encryption Process The content-encryption key for the desired content-encryption algorithm is randomly generated. The data to be protected is padded as described below, then the padded data is encrypted using the content-encryption key. The encryption operation maps an arbitrary string of octets (the data) to another string of octets (the ciphertext) under control of a content-encryption key. The encrypted data is included in the EnvelopedData encryptedContentInfo encryptedContent OCTET STRING. Housley Standards Track [Page 27]
RFC 5652 Cryptographic Message Syntax September 2009 Some content-encryption algorithms assume the input length is a multiple of k octets, where k is greater than one. For such algorithms, the input shall be padded at the trailing end with k-(lth mod k) octets all having value k-(lth mod k), where lth is the length of the input. In other words, the input is padded at the trailing end with one of the following strings: 01 -- if lth mod k = k-1 02 02 -- if lth mod k = k-2 . . . k k ... k k -- if lth mod k = 0 The padding can be removed unambiguously since all input is padded, including input values that are already a multiple of the block size, and no padding string is a suffix of another. This padding method is well defined if and only if k is less than 256. 6.4. Key-encryption Process The input to the key-encryption process -- the value supplied to the recipient's key-encryption algorithm -- is just the "value" of the content-encryption key. Any of the aforementioned key management techniques can be used for each recipient of the same encrypted content. 7. Digested-data Content Type The digested-data content type consists of content of any type and a message digest of the content. Typically, the digested-data content type is used to provide content integrity, and the result generally becomes an input to the enveloped-data content type. The following steps construct digested-data: 1. A message digest is computed on the content with a message-digest algorithm. 2. The message-digest algorithm and the message digest are collected together with the content into a DigestedData value. A recipient verifies the message digest by comparing the message digest to an independently computed message digest. Housley Standards Track [Page 28]
RFC 5652 Cryptographic Message Syntax September 2009 The following object identifier identifies the digested-data content type: id-digestedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 5 } The digested-data content type shall have ASN.1 type DigestedData: DigestedData ::= SEQUENCE { version CMSVersion, digestAlgorithm DigestAlgorithmIdentifier, encapContentInfo EncapsulatedContentInfo, digest Digest } Digest ::= OCTET STRING The fields of type DigestedData have the following meanings: version is the syntax version number. If the encapsulated content type is id-data, then the value of version MUST be 0; however, if the encapsulated content type is other than id-data, then the value of version MUST be 2. digestAlgorithm identifies the message digest algorithm, and any associated parameters, under which the content is digested. The message-digesting process is the same as in Section 5.4 in the case when there are no signed attributes. encapContentInfo is the content that is digested, as defined in Section 5.2. digest is the result of the message-digesting process. The ordering of the digestAlgorithm field, the encapContentInfo field, and the digest field makes it possible to process a DigestedData value in a single pass. 8. Encrypted-data Content Type The encrypted-data content type consists of encrypted content of any type. Unlike the enveloped-data content type, the encrypted-data content type has neither recipients nor encrypted content-encryption keys. Keys MUST be managed by other means. The typical application of the encrypted-data content type will be to encrypt the content of the data content type for local storage, perhaps where the encryption key is derived from a password. Housley Standards Track [Page 29]
RFC 5652 Cryptographic Message Syntax September 2009 The following object identifier identifies the encrypted-data content type: id-encryptedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 6 } The encrypted-data content type shall have ASN.1 type EncryptedData: EncryptedData ::= SEQUENCE { version CMSVersion, encryptedContentInfo EncryptedContentInfo, unprotectedAttrs [1] IMPLICIT UnprotectedAttributes OPTIONAL } The fields of type EncryptedData have the following meanings: version is the syntax version number. If unprotectedAttrs is present, then the version MUST be 2. If unprotectedAttrs is absent, then version MUST be 0. encryptedContentInfo is the encrypted content information, as defined in Section 6.1. unprotectedAttrs is a collection of attributes that are not encrypted. The field is optional. Useful attribute types are defined in Section 11. 9. Authenticated-data Content Type The authenticated-data content type consists of content of any type, a message authentication code (MAC), and encrypted authentication keys for one or more recipients. The combination of the MAC and one encrypted authentication key for a recipient is necessary for that recipient to verify the integrity of the content. Any type of content can be integrity protected for an arbitrary number of recipients. The process by which authenticated-data is constructed involves the following steps: 1. A message-authentication key for a particular message- authentication algorithm is generated at random. 2. The message-authentication key is encrypted for each recipient. The details of this encryption depend on the key management algorithm used. Housley Standards Track [Page 30]
RFC 5652 Cryptographic Message Syntax September 2009 3. For each recipient, the encrypted message-authentication key and other recipient-specific information are collected into a RecipientInfo value, defined in Section 6.2. 4. Using the message-authentication key, the originator computes a MAC value on the content. If the originator is authenticating any information in addition to the content (see Section 9.2), a message digest is calculated on the content, the message digest of the content and the other information are authenticated using the message-authentication key, and the result becomes the "MAC value". 9.1. AuthenticatedData Type The following object identifier identifies the authenticated-data content type: id-ct-authData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs-9(9) smime(16) ct(1) 2 } The authenticated-data content type shall have ASN.1 type AuthenticatedData: AuthenticatedData ::= SEQUENCE { version CMSVersion, originatorInfo [0] IMPLICIT OriginatorInfo OPTIONAL, recipientInfos RecipientInfos, macAlgorithm MessageAuthenticationCodeAlgorithm, digestAlgorithm [1] DigestAlgorithmIdentifier OPTIONAL, encapContentInfo EncapsulatedContentInfo, authAttrs [2] IMPLICIT AuthAttributes OPTIONAL, mac MessageAuthenticationCode, unauthAttrs [3] IMPLICIT UnauthAttributes OPTIONAL } AuthAttributes ::= SET SIZE (1..MAX) OF Attribute UnauthAttributes ::= SET SIZE (1..MAX) OF Attribute MessageAuthenticationCode ::= OCTET STRING The fields of type AuthenticatedData have the following meanings: version is the syntax version number. The version MUST be assigned as follows: Housley Standards Track [Page 31]
RFC 5652 Cryptographic Message Syntax September 2009 IF (originatorInfo is present) AND ((any certificates with a type of other are present) OR (any crls with a type of other are present)) THEN version is 3 ELSE IF ((originatorInfo is present) AND (any version 2 attribute certificates are present)) THEN version is 1 ELSE version is 0 originatorInfo optionally provides information about the originator. It is present only if required by the key management algorithm. It MAY contain certificates, attribute certificates, and CRLs, as defined in Section 6.1. recipientInfos is a collection of per-recipient information, as defined in Section 6.1. There MUST be at least one element in the collection. macAlgorithm is a message authentication code (MAC) algorithm identifier. It identifies the MAC algorithm, along with any associated parameters, used by the originator. Placement of the macAlgorithm field facilitates one-pass processing by the recipient. digestAlgorithm identifies the message digest algorithm, and any associated parameters, used to compute a message digest on the encapsulated content if authenticated attributes are present. The message digesting process is described in Section 9.2. Placement of the digestAlgorithm field facilitates one-pass processing by the recipient. If the digestAlgorithm field is present, then the authAttrs field MUST also be present. encapContentInfo is the content that is authenticated, as defined in Section 5.2. authAttrs is a collection of authenticated attributes. The authAttrs structure is optional, but it MUST be present if the content type of the EncapsulatedContentInfo value being authenticated is not id-data. If the authAttrs field is present, then the digestAlgorithm field MUST also be present. The AuthAttributes structure MUST be DER encoded, even if the rest of the structure is BER encoded. Useful attribute types are defined in Section 11. If the authAttrs field is present, it MUST contain, at a minimum, the following two attributes: Housley Standards Track [Page 32]
RFC 5652 Cryptographic Message Syntax September 2009 A content-type attribute having as its value the content type of the EncapsulatedContentInfo value being authenticated. Section 11.1 defines the content-type attribute. A message-digest attribute, having as its value the message digest of the content. Section 11.2 defines the message-digest attribute. mac is the message authentication code. unauthAttrs is a collection of attributes that are not authenticated. The field is optional. To date, no attributes have been defined for use as unauthenticated attributes, but other useful attribute types are defined in Section 11. 9.2. MAC Generation The MAC calculation process computes a message authentication code (MAC) on either the content being authenticated or a message digest of content being authenticated together with the originator's authenticated attributes. If the authAttrs field is absent, the input to the MAC calculation process is the value of the encapContentInfo eContent OCTET STRING. Only the octets comprising the value of the eContent OCTET STRING are input to the MAC algorithm; the tag and the length octets are omitted. This has the advantage that the length of the content being authenticated need not be known in advance of the MAC generation process. If the authAttrs field is present, the content-type attribute (as described in Section 11.1) and the message-digest attribute (as described in Section 11.2) MUST be included, and the input to the MAC calculation process is the DER encoding of authAttrs. A separate encoding of the authAttrs field is performed for message digest calculation. The IMPLICIT [2] tag in the authAttrs field is not used for the DER encoding, rather an EXPLICIT SET OF tag is used. That is, the DER encoding of the SET OF tag, rather than of the IMPLICIT [2] tag, is to be included in the message digest calculation along with the length and content octets of the authAttrs value. The message digest calculation process computes a message digest on the content being authenticated. The initial input to the message digest calculation process is the "value" of the encapsulated content being authenticated. Specifically, the input is the encapContentInfo eContent OCTET STRING to which the authentication process is applied. Only the octets comprising the value of the encapContentInfo eContent OCTET STRING are input to the message digest algorithm, not the tag Housley Standards Track [Page 33]
RFC 5652 Cryptographic Message Syntax September 2009 or the length octets. This has the advantage that the length of the content being authenticated need not be known in advance. Although the encapContentInfo eContent OCTET STRING tag and length octets are not included in the message digest calculation, they are still protected by other means. The length octets are protected by the nature of the message digest algorithm since it is computationally infeasible to find any two distinct contents of any length that have the same message digest. The input to the MAC calculation process includes the MAC input data, defined above, and an authentication key conveyed in a recipientInfo structure. The details of MAC calculation depend on the MAC algorithm employed (e.g., Hashed Message Authentication Code (HMAC)). The object identifier, along with any parameters, that specifies the MAC algorithm employed by the originator is carried in the macAlgorithm field. The MAC value generated by the originator is encoded as an OCTET STRING and carried in the mac field. 9.3. MAC Verification The input to the MAC verification process includes the input data (determined based on the presence or absence of the authAttrs field, as defined in 9.2), and the authentication key conveyed in recipientInfo. The details of the MAC verification process depend on the MAC algorithm employed. The recipient MUST NOT rely on any MAC values or message digest values computed by the originator. The content is authenticated as described in Section 9.2. If the originator includes authenticated attributes, then the content of the authAttrs is authenticated as described in Section 9.2. For authentication to succeed, the MAC value calculated by the recipient MUST be the same as the value of the mac field. Similarly, for authentication to succeed when the authAttrs field is present, the content message digest value calculated by the recipient MUST be the same as the message digest value included in the authAttrs message-digest attribute. If the AuthenticatedData includes authAttrs, then the content-type attribute value MUST match the AuthenticatedData encapContentInfo eContentType value. 10. Useful Types This section is divided into two parts. The first part defines algorithm identifiers, and the second part defines other useful types. Housley Standards Track [Page 34]
RFC 5652 Cryptographic Message Syntax September 2009 10.1. Algorithm Identifier Types All of the algorithm identifiers have the same type: AlgorithmIdentifier. The definition of AlgorithmIdentifier is taken from X.509 [X.509-88]. There are many alternatives for each algorithm type. 10.1.1. DigestAlgorithmIdentifier The DigestAlgorithmIdentifier type identifies a message-digest algorithm. Examples include SHA-1, MD2, and MD5. A message-digest algorithm maps an octet string (the content) to another octet string (the message digest). DigestAlgorithmIdentifier ::= AlgorithmIdentifier 10.1.2. SignatureAlgorithmIdentifier The SignatureAlgorithmIdentifier type identifies a signature algorithm, and it can also identify a message digest algorithm. Examples include RSA, DSA, DSA with SHA-1, ECDSA, and ECDSA with SHA-256. A signature algorithm supports signature generation and verification operations. The signature generation operation uses the message digest and the signer's private key to generate a signature value. The signature verification operation uses the message digest and the signer's public key to determine whether or not a signature value is valid. Context determines which operation is intended. SignatureAlgorithmIdentifier ::= AlgorithmIdentifier 10.1.3. KeyEncryptionAlgorithmIdentifier The KeyEncryptionAlgorithmIdentifier type identifies a key-encryption algorithm used to encrypt a content-encryption key. The encryption operation maps an octet string (the key) to another octet string (the encrypted key) under control of a key-encryption key. The decryption operation is the inverse of the encryption operation. Context determines which operation is intended. The details of encryption and decryption depend on the key management algorithm used. Key transport, key agreement, previously distributed symmetric key-encrypting keys, and symmetric key-encrypting keys derived from passwords are supported. KeyEncryptionAlgorithmIdentifier ::= AlgorithmIdentifier Housley Standards Track [Page 35]
RFC 5652 Cryptographic Message Syntax September 2009 10.1.4. ContentEncryptionAlgorithmIdentifier The ContentEncryptionAlgorithmIdentifier type identifies a content- encryption algorithm. Examples include Triple-DES and RC2. A content-encryption algorithm supports encryption and decryption operations. The encryption operation maps an octet string (the plaintext) to another octet string (the ciphertext) under control of a content-encryption key. The decryption operation is the inverse of the encryption operation. Context determines which operation is intended. ContentEncryptionAlgorithmIdentifier ::= AlgorithmIdentifier 10.1.5. MessageAuthenticationCodeAlgorithm The MessageAuthenticationCodeAlgorithm type identifies a message authentication code (MAC) algorithm. Examples include DES-MAC and HMAC-SHA-1. A MAC algorithm supports generation and verification operations. The MAC generation and verification operations use the same symmetric key. Context determines which operation is intended. MessageAuthenticationCodeAlgorithm ::= AlgorithmIdentifier 10.1.6. KeyDerivationAlgorithmIdentifier The KeyDerivationAlgorithmIdentifier type is specified in RFC 3211 [PWRI]. The KeyDerivationAlgorithmIdentifier definition is repeated here for completeness. Key derivation algorithms convert a password or shared secret value into a key-encryption key. KeyDerivationAlgorithmIdentifier ::= AlgorithmIdentifier 10.2. Other Useful Types This section defines types that are used other places in the document. The types are not listed in any particular order. 10.2.1. RevocationInfoChoices The RevocationInfoChoices type gives a set of revocation status information alternatives. It is intended that the set contain information sufficient to determine whether the certificates and attribute certificates with which the set is associated are revoked. However, there MAY be more revocation status information than necessary or there MAY be less revocation status information than necessary. X.509 Certificate revocation lists (CRLs) [X.509-97] are Housley Standards Track [Page 36]
RFC 5652 Cryptographic Message Syntax September 2009 the primary source of revocation status information, but any other revocation information format can be supported. The OtherRevocationInfoFormat alternative is provided to support any other revocation information format without further modifications to the CMS. For example, Online Certificate Status Protocol (OCSP) Responses [OCSP] can be supported using the OtherRevocationInfoFormat. The CertificateList may contain a CRL, an Authority Revocation List (ARL), a Delta CRL, or an Attribute Certificate Revocation List. All of these lists share a common syntax. The CertificateList type gives a certificate revocation list (CRL). CRLs are specified in X.509 [X.509-97], and they are profiled for use in the Internet in RFC 5280 [PROFILE]. The definition of CertificateList is taken from X.509. RevocationInfoChoices ::= SET OF RevocationInfoChoice RevocationInfoChoice ::= CHOICE { crl CertificateList, other [1] IMPLICIT OtherRevocationInfoFormat } OtherRevocationInfoFormat ::= SEQUENCE { otherRevInfoFormat OBJECT IDENTIFIER, otherRevInfo ANY DEFINED BY otherRevInfoFormat } 10.2.2. CertificateChoices The CertificateChoices type gives either a PKCS #6 extended certificate [PKCS#6], an X.509 certificate, a version 1 X.509 attribute certificate (ACv1) [X.509-97], a version 2 X.509 attribute certificate (ACv2) [X.509-00], or any other certificate format. The PKCS #6 extended certificate is obsolete. The PKCS #6 certificate is included for backward compatibility, and PKCS #6 certificates SHOULD NOT be used. The ACv1 is also obsolete. ACv1 is included for backward compatibility, and ACv1 SHOULD NOT be used. The Internet profile of X.509 certificates is specified in the "Internet X.509 Public Key Infrastructure: Certificate and CRL Profile" [PROFILE]. The Internet profile of ACv2 is specified in the "An Internet Attribute Certificate Profile for Authorization" [ACPROFILE]. The OtherCertificateFormat alternative is provided to support any other certificate format without further modifications to the CMS. The definition of Certificate is taken from X.509. Housley Standards Track [Page 37]
RFC 5652 Cryptographic Message Syntax September 2009 The definitions of AttributeCertificate are taken from X.509-1997 and X.509-2000. The definition from X.509-1997 is assigned to AttributeCertificateV1 (see Section 12.2), and the definition from X.509-2000 is assigned to AttributeCertificateV2. CertificateChoices ::= CHOICE { certificate Certificate, extendedCertificate [0] IMPLICIT ExtendedCertificate, -- Obsolete v1AttrCert [1] IMPLICIT AttributeCertificateV1, -- Obsolete v2AttrCert [2] IMPLICIT AttributeCertificateV2, other [3] IMPLICIT OtherCertificateFormat } OtherCertificateFormat ::= SEQUENCE { otherCertFormat OBJECT IDENTIFIER, otherCert ANY DEFINED BY otherCertFormat } 10.2.3. CertificateSet The CertificateSet type provides a set of certificates. It is intended that the set be sufficient to contain certification paths from a recognized "root" or "top-level certification authority" to all of the sender certificates with which the set is associated. However, there may be more certificates than necessary, or there MAY be fewer than necessary. The precise meaning of a "certification path" is outside the scope of this document. However, [PROFILE] provides a definition for X.509 certificates. Some applications may impose upper limits on the length of a certification path; others may enforce certain relationships between the subjects and issuers of certificates within a certification path. CertificateSet ::= SET OF CertificateChoices 10.2.4. IssuerAndSerialNumber The IssuerAndSerialNumber type identifies a certificate, and thereby an entity and a public key, by the distinguished name of the certificate issuer and an issuer-specific certificate serial number. The definition of Name is taken from X.501 [X.501-88], and the definition of CertificateSerialNumber is taken from X.509 [X.509-97]. IssuerAndSerialNumber ::= SEQUENCE { issuer Name, serialNumber CertificateSerialNumber } CertificateSerialNumber ::= INTEGER Housley Standards Track [Page 38]
RFC 5652 Cryptographic Message Syntax September 2009 10.2.5. CMSVersion The CMSVersion type gives a syntax version number, for compatibility with future revisions of this specification. CMSVersion ::= INTEGER { v0(0), v1(1), v2(2), v3(3), v4(4), v5(5) } 10.2.6. UserKeyingMaterial The UserKeyingMaterial type gives a syntax for user keying material (UKM). Some key agreement algorithms require UKMs to ensure that a different key is generated each time the same two parties generate a pairwise key. The sender provides a UKM for use with a specific key agreement algorithm. UserKeyingMaterial ::= OCTET STRING 10.2.7. OtherKeyAttribute The OtherKeyAttribute type gives a syntax for the inclusion of other key attributes that permit the recipient to select the key used by the sender. The attribute object identifier must be registered along with the syntax of the attribute itself. Use of this structure should be avoided since it might impede interoperability. OtherKeyAttribute ::= SEQUENCE { keyAttrId OBJECT IDENTIFIER, keyAttr ANY DEFINED BY keyAttrId OPTIONAL } 11. Useful Attributes This section defines attributes that may be used with signed-data, enveloped-data, encrypted-data, or authenticated-data. The syntax of Attribute is compatible with X.501 [X.501-88] and RFC 5280 [PROFILE]. Some of the attributes defined in this section were originally defined in PKCS #9 [PKCS#9]; others were originally defined in a previous version of this specification [CMS1]. The attributes are not listed in any particular order. Additional attributes are defined in many places, notably the S/MIME Version 3.1 Message Specification [MSG3.1] and the Enhanced Security Services for S/MIME [ESS], which also include recommendations on the placement of these attributes. Housley Standards Track [Page 39]
RFC 5652 Cryptographic Message Syntax September 2009 11.1. Content Type The content-type attribute type specifies the content type of the ContentInfo within signed-data or authenticated-data. The content- type attribute type MUST be present whenever signed attributes are present in signed-data or authenticated attributes present in authenticated-data. The content-type attribute value MUST match the encapContentInfo eContentType value in the signed-data or authenticated-data. The content-type attribute MUST be a signed attribute or an authenticated attribute; it MUST NOT be an unsigned attribute, unauthenticated attribute, or unprotected attribute. The following object identifier identifies the content-type attribute: id-contentType OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 3 } Content-type attribute values have ASN.1 type ContentType: ContentType ::= OBJECT IDENTIFIER Even though the syntax is defined as a SET OF AttributeValue, a content-type attribute MUST have a single attribute value; zero or multiple instances of AttributeValue are not permitted. The SignedAttributes and AuthAttributes syntaxes are each defined as a SET OF Attributes. The SignedAttributes in a signerInfo MUST NOT include multiple instances of the content-type attribute. Similarly, the AuthAttributes in an AuthenticatedData MUST NOT include multiple instances of the content-type attribute. 11.2. Message Digest The message-digest attribute type specifies the message digest of the encapContentInfo eContent OCTET STRING being signed in signed-data (see Section 5.4) or authenticated in authenticated-data (see Section 9.2). For signed-data, the message digest is computed using the signer's message digest algorithm. For authenticated-data, the message digest is computed using the originator's message digest algorithm. Within signed-data, the message-digest signed attribute type MUST be present when there are any signed attributes present. Within authenticated-data, the message-digest authenticated attribute type MUST be present when there are any authenticated attributes present. Housley Standards Track [Page 40]
RFC 5652 Cryptographic Message Syntax September 2009 The message-digest attribute MUST be a signed attribute or an authenticated attribute; it MUST NOT be an unsigned attribute, unauthenticated attribute, or unprotected attribute. The following object identifier identifies the message-digest attribute: id-messageDigest OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 4 } Message-digest attribute values have ASN.1 type MessageDigest: MessageDigest ::= OCTET STRING A message-digest attribute MUST have a single attribute value, even though the syntax is defined as a SET OF AttributeValue. There MUST NOT be zero or multiple instances of AttributeValue present. The SignedAttributes syntax and AuthAttributes syntax are each defined as a SET OF Attributes. The SignedAttributes in a signerInfo MUST include only one instance of the message-digest attribute. Similarly, the AuthAttributes in an AuthenticatedData MUST include only one instance of the message-digest attribute. 11.3. Signing Time The signing-time attribute type specifies the time at which the signer (purportedly) performed the signing process. The signing-time attribute type is intended for use in signed-data. The signing-time attribute MUST be a signed attribute or an authenticated attribute; it MUST NOT be an unsigned attribute, unauthenticated attribute, or unprotected attribute. The following object identifier identifies the signing-time attribute: id-signingTime OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 5 } Signing-time attribute values have ASN.1 type SigningTime: SigningTime ::= Time Time ::= CHOICE { utcTime UTCTime, generalizedTime GeneralizedTime } Housley Standards Track [Page 41]
RFC 5652 Cryptographic Message Syntax September 2009 Note: The definition of Time matches the one specified in the 1997 version of X.509 [X.509-97]. Dates between 1 January 1950 and 31 December 2049 (inclusive) MUST be encoded as UTCTime. Any dates with year values before 1950 or after 2049 MUST be encoded as GeneralizedTime. UTCTime values MUST be expressed in Coordinated Universal Time (formerly known as Greenwich Mean Time (GMT) and Zulu clock time) and MUST include seconds (i.e., times are YYMMDDHHMMSSZ), even where the number of seconds is zero. Midnight MUST be represented as "YYMMDD000000Z". Century information is implicit, and the century MUST be determined as follows: Where YY is greater than or equal to 50, the year MUST be interpreted as 19YY; and Where YY is less than 50, the year MUST be interpreted as 20YY. GeneralizedTime values MUST be expressed in Coordinated Universal Time and MUST include seconds (i.e., times are YYYYMMDDHHMMSSZ), even where the number of seconds is zero. GeneralizedTime values MUST NOT include fractional seconds. A signing-time attribute MUST have a single attribute value, even though the syntax is defined as a SET OF AttributeValue. There MUST NOT be zero or multiple instances of AttributeValue present. The SignedAttributes syntax and the AuthAttributes syntax are each defined as a SET OF Attributes. The SignedAttributes in a signerInfo MUST NOT include multiple instances of the signing-time attribute. Similarly, the AuthAttributes in an AuthenticatedData MUST NOT include multiple instances of the signing-time attribute. No requirement is imposed concerning the correctness of the signing time, and acceptance of a purported signing time is a matter of a recipient's discretion. It is expected, however, that some signers, such as time-stamp servers, will be trusted implicitly. 11.4. Countersignature The countersignature attribute type specifies one or more signatures on the contents octets of the signature OCTET STRING in a SignerInfo value of the signed-data. That is, the message digest is computed over the octets comprising the value of the OCTET STRING, neither the tag nor length octets are included. Thus, the countersignature attribute type countersigns (signs in serial) another signature. Housley Standards Track [Page 42]
RFC 5652 Cryptographic Message Syntax September 2009 The countersignature attribute MUST be an unsigned attribute; it MUST NOT be a signed attribute, an authenticated attribute, an unauthenticated attribute, or an unprotected attribute. The following object identifier identifies the countersignature attribute: id-countersignature OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 6 } Countersignature attribute values have ASN.1 type Countersignature: Countersignature ::= SignerInfo Countersignature values have the same meaning as SignerInfo values for ordinary signatures, except that: 1. The signedAttributes field MUST NOT contain a content-type attribute; there is no content type for countersignatures. 2. The signedAttributes field MUST contain a message-digest attribute if it contains any other attributes. 3. The input to the message-digesting process is the contents octets of the DER encoding of the signatureValue field of the SignerInfo value with which the attribute is associated. A countersignature attribute can have multiple attribute values. The syntax is defined as a SET OF AttributeValue, and there MUST be one or more instances of AttributeValue present. The UnsignedAttributes syntax is defined as a SET OF Attributes. The UnsignedAttributes in a signerInfo may include multiple instances of the countersignature attribute. A countersignature, since it has type SignerInfo, can itself contain a countersignature attribute. Thus, it is possible to construct an arbitrarily long series of countersignatures. 12. ASN.1 Modules Section 12.1 contains the ASN.1 module for the CMS, and Section 12.2 contains the ASN.1 module for the Version 1 Attribute Certificate. Housley Standards Track [Page 43]
RFC 5652 Cryptographic Message Syntax September 2009 12.1. CMS ASN.1 Module CryptographicMessageSyntax2004 { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs-9(9) smime(16) modules(0) cms-2004(24) } DEFINITIONS IMPLICIT TAGS ::= BEGIN -- EXPORTS All -- The types and values defined in this module are exported for use -- in the other ASN.1 modules. Other applications may use them for -- their own purposes. IMPORTS -- Imports from RFC 5280 [PROFILE], Appendix A.1 AlgorithmIdentifier, Certificate, CertificateList, CertificateSerialNumber, Name FROM PKIX1Explicit88 { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) mod(0) pkix1-explicit(18) } -- Imports from RFC 3281 [ACPROFILE], Appendix B AttributeCertificate FROM PKIXAttributeCertificate { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) mod(0) attribute-cert(12) } -- Imports from Appendix B of this document AttributeCertificateV1 FROM AttributeCertificateVersion1 { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs-9(9) smime(16) modules(0) v1AttrCert(15) } ; -- Cryptographic Message Syntax ContentInfo ::= SEQUENCE { contentType ContentType, content [0] EXPLICIT ANY DEFINED BY contentType } ContentType ::= OBJECT IDENTIFIER Housley Standards Track [Page 44]
RFC 5652 Cryptographic Message Syntax September 2009 SignedData ::= SEQUENCE { version CMSVersion, digestAlgorithms DigestAlgorithmIdentifiers, encapContentInfo EncapsulatedContentInfo, certificates [0] IMPLICIT CertificateSet OPTIONAL, crls [1] IMPLICIT RevocationInfoChoices OPTIONAL, signerInfos SignerInfos } DigestAlgorithmIdentifiers ::= SET OF DigestAlgorithmIdentifier SignerInfos ::= SET OF SignerInfo EncapsulatedContentInfo ::= SEQUENCE { eContentType ContentType, eContent [0] EXPLICIT OCTET STRING OPTIONAL } SignerInfo ::= SEQUENCE { version CMSVersion, sid SignerIdentifier, digestAlgorithm DigestAlgorithmIdentifier, signedAttrs [0] IMPLICIT SignedAttributes OPTIONAL, signatureAlgorithm SignatureAlgorithmIdentifier, signature SignatureValue, unsignedAttrs [1] IMPLICIT UnsignedAttributes OPTIONAL } SignerIdentifier ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, subjectKeyIdentifier [0] SubjectKeyIdentifier } SignedAttributes ::= SET SIZE (1..MAX) OF Attribute UnsignedAttributes ::= SET SIZE (1..MAX) OF Attribute Attribute ::= SEQUENCE { attrType OBJECT IDENTIFIER, attrValues SET OF AttributeValue } AttributeValue ::= ANY SignatureValue ::= OCTET STRING EnvelopedData ::= SEQUENCE { version CMSVersion, originatorInfo [0] IMPLICIT OriginatorInfo OPTIONAL, recipientInfos RecipientInfos, encryptedContentInfo EncryptedContentInfo, unprotectedAttrs [1] IMPLICIT UnprotectedAttributes OPTIONAL } Housley Standards Track [Page 45]
RFC 5652 Cryptographic Message Syntax September 2009 OriginatorInfo ::= SEQUENCE { certs [0] IMPLICIT CertificateSet OPTIONAL, crls [1] IMPLICIT RevocationInfoChoices OPTIONAL } RecipientInfos ::= SET SIZE (1..MAX) OF RecipientInfo EncryptedContentInfo ::= SEQUENCE { contentType ContentType, contentEncryptionAlgorithm ContentEncryptionAlgorithmIdentifier, encryptedContent [0] IMPLICIT EncryptedContent OPTIONAL } EncryptedContent ::= OCTET STRING UnprotectedAttributes ::= SET SIZE (1..MAX) OF Attribute RecipientInfo ::= CHOICE { ktri KeyTransRecipientInfo, kari [1] KeyAgreeRecipientInfo, kekri [2] KEKRecipientInfo, pwri [3] PasswordRecipientInfo, ori [4] OtherRecipientInfo } EncryptedKey ::= OCTET STRING KeyTransRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 0 or 2 rid RecipientIdentifier, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, encryptedKey EncryptedKey } RecipientIdentifier ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, subjectKeyIdentifier [0] SubjectKeyIdentifier } KeyAgreeRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 3 originator [0] EXPLICIT OriginatorIdentifierOrKey, ukm [1] EXPLICIT UserKeyingMaterial OPTIONAL, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, recipientEncryptedKeys RecipientEncryptedKeys } OriginatorIdentifierOrKey ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, subjectKeyIdentifier [0] SubjectKeyIdentifier, originatorKey [1] OriginatorPublicKey } Housley Standards Track [Page 46]
RFC 5652 Cryptographic Message Syntax September 2009 OriginatorPublicKey ::= SEQUENCE { algorithm AlgorithmIdentifier, publicKey BIT STRING } RecipientEncryptedKeys ::= SEQUENCE OF RecipientEncryptedKey RecipientEncryptedKey ::= SEQUENCE { rid KeyAgreeRecipientIdentifier, encryptedKey EncryptedKey } KeyAgreeRecipientIdentifier ::= CHOICE { issuerAndSerialNumber IssuerAndSerialNumber, rKeyId [0] IMPLICIT RecipientKeyIdentifier } RecipientKeyIdentifier ::= SEQUENCE { subjectKeyIdentifier SubjectKeyIdentifier, date GeneralizedTime OPTIONAL, other OtherKeyAttribute OPTIONAL } SubjectKeyIdentifier ::= OCTET STRING KEKRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 4 kekid KEKIdentifier, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, encryptedKey EncryptedKey } KEKIdentifier ::= SEQUENCE { keyIdentifier OCTET STRING, date GeneralizedTime OPTIONAL, other OtherKeyAttribute OPTIONAL } PasswordRecipientInfo ::= SEQUENCE { version CMSVersion, -- always set to 0 keyDerivationAlgorithm [0] KeyDerivationAlgorithmIdentifier OPTIONAL, keyEncryptionAlgorithm KeyEncryptionAlgorithmIdentifier, encryptedKey EncryptedKey } OtherRecipientInfo ::= SEQUENCE { oriType OBJECT IDENTIFIER, oriValue ANY DEFINED BY oriType } DigestedData ::= SEQUENCE { version CMSVersion, digestAlgorithm DigestAlgorithmIdentifier, encapContentInfo EncapsulatedContentInfo, digest Digest } Housley Standards Track [Page 47]
RFC 5652 Cryptographic Message Syntax September 2009 Digest ::= OCTET STRING EncryptedData ::= SEQUENCE { version CMSVersion, encryptedContentInfo EncryptedContentInfo, unprotectedAttrs [1] IMPLICIT UnprotectedAttributes OPTIONAL } AuthenticatedData ::= SEQUENCE { version CMSVersion, originatorInfo [0] IMPLICIT OriginatorInfo OPTIONAL, recipientInfos RecipientInfos, macAlgorithm MessageAuthenticationCodeAlgorithm, digestAlgorithm [1] DigestAlgorithmIdentifier OPTIONAL, encapContentInfo EncapsulatedContentInfo, authAttrs [2] IMPLICIT AuthAttributes OPTIONAL, mac MessageAuthenticationCode, unauthAttrs [3] IMPLICIT UnauthAttributes OPTIONAL } AuthAttributes ::= SET SIZE (1..MAX) OF Attribute UnauthAttributes ::= SET SIZE (1..MAX) OF Attribute MessageAuthenticationCode ::= OCTET STRING DigestAlgorithmIdentifier ::= AlgorithmIdentifier SignatureAlgorithmIdentifier ::= AlgorithmIdentifier KeyEncryptionAlgorithmIdentifier ::= AlgorithmIdentifier ContentEncryptionAlgorithmIdentifier ::= AlgorithmIdentifier MessageAuthenticationCodeAlgorithm ::= AlgorithmIdentifier KeyDerivationAlgorithmIdentifier ::= AlgorithmIdentifier RevocationInfoChoices ::= SET OF RevocationInfoChoice RevocationInfoChoice ::= CHOICE { crl CertificateList, other [1] IMPLICIT OtherRevocationInfoFormat } OtherRevocationInfoFormat ::= SEQUENCE { otherRevInfoFormat OBJECT IDENTIFIER, otherRevInfo ANY DEFINED BY otherRevInfoFormat } Housley Standards Track [Page 48]
RFC 5652 Cryptographic Message Syntax September 2009 CertificateChoices ::= CHOICE { certificate Certificate, extendedCertificate [0] IMPLICIT ExtendedCertificate, -- Obsolete v1AttrCert [1] IMPLICIT AttributeCertificateV1, -- Obsolete v2AttrCert [2] IMPLICIT AttributeCertificateV2, other [3] IMPLICIT OtherCertificateFormat } AttributeCertificateV2 ::= AttributeCertificate OtherCertificateFormat ::= SEQUENCE { otherCertFormat OBJECT IDENTIFIER, otherCert ANY DEFINED BY otherCertFormat } CertificateSet ::= SET OF CertificateChoices IssuerAndSerialNumber ::= SEQUENCE { issuer Name, serialNumber CertificateSerialNumber } CMSVersion ::= INTEGER { v0(0), v1(1), v2(2), v3(3), v4(4), v5(5) } UserKeyingMaterial ::= OCTET STRING OtherKeyAttribute ::= SEQUENCE { keyAttrId OBJECT IDENTIFIER, keyAttr ANY DEFINED BY keyAttrId OPTIONAL } -- Content Type Object Identifiers id-ct-contentInfo OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) smime(16) ct(1) 6 } id-data OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 1 } id-signedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 2 } id-envelopedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 3 } id-digestedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 5 } id-encryptedData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs7(7) 6 } Housley Standards Track [Page 49]
RFC 5652 Cryptographic Message Syntax September 2009 id-ct-authData OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs-9(9) smime(16) ct(1) 2 } -- The CMS Attributes MessageDigest ::= OCTET STRING SigningTime ::= Time Time ::= CHOICE { utcTime UTCTime, generalTime GeneralizedTime } Countersignature ::= SignerInfo -- Attribute Object Identifiers id-contentType OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 3 } id-messageDigest OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 4 } id-signingTime OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 5 } id-countersignature OBJECT IDENTIFIER ::= { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs9(9) 6 } -- Obsolete Extended Certificate syntax from PKCS #6 ExtendedCertificateOrCertificate ::= CHOICE { certificate Certificate, extendedCertificate [0] IMPLICIT ExtendedCertificate } ExtendedCertificate ::= SEQUENCE { extendedCertificateInfo ExtendedCertificateInfo, signatureAlgorithm SignatureAlgorithmIdentifier, signature Signature } ExtendedCertificateInfo ::= SEQUENCE { version CMSVersion, certificate Certificate, attributes UnauthAttributes } Signature ::= BIT STRING END -- of CryptographicMessageSyntax2004 Housley Standards Track [Page 50]
RFC 5652 Cryptographic Message Syntax September 2009 12.2. Version 1 Attribute Certificate ASN.1 Module AttributeCertificateVersion1 { iso(1) member-body(2) us(840) rsadsi(113549) pkcs(1) pkcs-9(9) smime(16) modules(0) v1AttrCert(15) } DEFINITIONS EXPLICIT TAGS ::= BEGIN -- EXPORTS All IMPORTS -- Imports from RFC 5280 [PROFILE], Appendix A.1 AlgorithmIdentifier, Attribute, CertificateSerialNumber, Extensions, UniqueIdentifier FROM PKIX1Explicit88 { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) mod(0) pkix1-explicit(18) } -- Imports from RFC 5280 [PROFILE], Appendix A.2 GeneralNames FROM PKIX1Implicit88 { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) mod(0) pkix1-implicit(19) } -- Imports from RFC 3281 [ACPROFILE], Appendix B AttCertValidityPeriod, IssuerSerial FROM PKIXAttributeCertificate { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) mod(0) attribute-cert(12) } ; -- Definition extracted from X.509-1997 [X.509-97], but -- different type names are used to avoid collisions. AttributeCertificateV1 ::= SEQUENCE { acInfo AttributeCertificateInfoV1, signatureAlgorithm AlgorithmIdentifier, signature BIT STRING } Housley Standards Track [Page 51]
RFC 5652 Cryptographic Message Syntax September 2009 AttributeCertificateInfoV1 ::= SEQUENCE { version AttCertVersionV1 DEFAULT v1, subject CHOICE { baseCertificateID [0] IssuerSerial, -- associated with a Public Key Certificate subjectName [1] GeneralNames }, -- associated with a name issuer GeneralNames, signature AlgorithmIdentifier, serialNumber CertificateSerialNumber, attCertValidityPeriod AttCertValidityPeriod, attributes SEQUENCE OF Attribute, issuerUniqueID UniqueIdentifier OPTIONAL, extensions Extensions OPTIONAL } AttCertVersionV1 ::= INTEGER { v1(0) } END -- of AttributeCertificateVersion1 13. References 13.1. Normative References [ACPROFILE] Farrell, S. and R. Housley, "An Internet Attribute Certificate Profile for Authorization", RFC 3281, April 2002. [PROFILE] Cooper, D., Santesson, S., Farrell, S., Boeyen, S., Housley, R., and W. Polk, "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation List (CRL) Profile", RFC 5280, May 2008. [STDWORDS] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [X.208-88] CCITT. Recommendation X.208: Specification of Abstract Syntax Notation One (ASN.1), 1988. [X.209-88] CCITT. Recommendation X.209: Specification of Basic Encoding Rules for Abstract Syntax Notation One (ASN.1), 1988. [X.501-88] CCITT. Recommendation X.501: The Directory - Models, 1988. [X.509-88] CCITT. Recommendation X.509: The Directory - Authentication Framework, 1988. Housley Standards Track [Page 52]
RFC 5652 Cryptographic Message Syntax September 2009 [X.509-97] ITU-T. Recommendation X.509: The Directory - Authentication Framework, 1997. [X.509-00] ITU-T. Recommendation X.509: The Directory - Authentication Framework, 2000. 13.2. Informative References [CMS1] Housley, R., "Cryptographic Message Syntax", RFC 2630, June 1999. [CMS2] Housley, R., "Cryptographic Message Syntax (CMS)", RFC 3369, August 2002. [CMS3] Housley, R., "Cryptographic Message Syntax (CMS)", RFC 3852, July 2004. [CMSALG] Housley, R., "Cryptographic Message Syntax (CMS) Algorithms", RFC 3370, August 2002. [CMSMSIG] Housley, R., "Cryptographic Message Syntax (CMS) Multiple Signer Clarification", RFC 4853, April 2007. [DH-X9.42] Rescorla, E., "Diffie-Hellman Key Agreement Method", RFC 2631, June 1999. [ESS] Hoffman, P., Ed., "Enhanced Security Services for S/MIME", RFC 2634, June 1999. [MSAC] Microsoft Development Network (MSDN) Library, "Authenticode", April 2004 Release. [MSG2] Dusse, S., Hoffman, P., Ramsdell, B., Lundblade, L., and L. Repka, "S/MIME Version 2 Message Specification", RFC 2311, March 1998. [MSG3] Ramsdell, B., Ed., "S/MIME Version 3 Message Specification", RFC 2633, June 1999. [MSG3.1] Ramsdell, B., Ed., "Secure/Multipurpose Internet Mail Extensions (S/MIME) Version 3.1 Message Specification", RFC 3851, July 2004. [NEWPKCS#1] Kaliski, B. and J. Staddon, "PKCS #1: RSA Cryptography Specifications Version 2.0", RFC 2437, October 1998. Housley Standards Track [Page 53]
RFC 5652 Cryptographic Message Syntax September 2009 [OCSP] Myers, M., Ankney, R., Malpani, A., Galperin, S., and C. Adams, "X.509 Internet Public Key Infrastructure Online Certificate Status Protocol - OCSP", RFC 2560, June 1999. [PKCS#1] Kaliski, B., "PKCS #1: RSA Encryption Version 1.5", RFC 2313, March 1998. [PKCS#6] RSA Laboratories. PKCS #6: Extended-Certificate Syntax Standard, Version 1.5. November 1993. [PKCS#7] Kaliski, B., "PKCS #7: Cryptographic Message Syntax Version 1.5", RFC 2315, March 1998. [PKCS#9] RSA Laboratories. PKCS #9: Selected Attribute Types, Version 1.1. November 1993. [PWRI] Gutmann, P., "Password-based Encryption for CMS", RFC 3211, December 2001. [RANDOM] Eastlake, D., 3rd, Schiller, J., and S. Crocker, "Randomness Requirements for Security", BCP 106, RFC 4086, June 2005. 14. Security Considerations The Cryptographic Message Syntax provides a method for digitally signing data, digesting data, encrypting data, and authenticating data. Implementations must protect the signer's private key. Compromise of the signer's private key permits masquerade. Implementations must protect the key management private key, the key-encryption key, and the content-encryption key. Compromise of the key management private key or the key-encryption key may result in the disclosure of all contents protected with that key. Similarly, compromise of the content-encryption key may result in disclosure of the associated encrypted content. Implementations must protect the key management private key and the message-authentication key. Compromise of the key management private key permits masquerade of authenticated data. Similarly, compromise of the message-authentication key may result in undetectable modification of the authenticated content. Housley Standards Track [Page 54]
RFC 5652 Cryptographic Message Syntax September 2009 The key management technique employed to distribute message- authentication keys must itself provide data origin authentication; otherwise, the contents are delivered with integrity from an unknown source. Neither RSA [PKCS#1] [NEWPKCS#1] nor Ephemeral-Static Diffie-Hellman [DH-X9.42] provide the necessary data origin authentication. Static-Static Diffie-Hellman [DH-X9.42] does provide the necessary data origin authentication when both the originator and recipient public keys are bound to appropriate identities in X.509 certificates. When more than two parties share the same message-authentication key, data origin authentication is not provided. Any party that knows the message-authentication key can compute a valid MAC; therefore, the contents could originate from any one of the parties. Implementations must randomly generate content-encryption keys, message-authentication keys, initialization vectors (IVs), and padding. Also, the generation of public/private key pairs relies on random numbers. The use of inadequate pseudo-random number generators (PRNGs) to generate cryptographic keys can result in little or no security. An attacker may find it much easier to reproduce the PRNG environment that produced the keys, searching the resulting small set of possibilities, rather than brute force searching the whole key space. The generation of quality random numbers is difficult. RFC 4086 [RANDOM] offers important guidance in this area. When using key-agreement algorithms or previously distributed symmetric key-encryption keys, a key-encryption key is used to encrypt the content-encryption key. If the key-encryption and content-encryption algorithms are different, the effective security is determined by the weaker of the two algorithms. If, for example, content is encrypted with Triple-DES using a 168-bit Triple-DES content-encryption key, and the content-encryption key is wrapped with RC2 using a 40-bit RC2 key-encryption key, then at most 40 bits of protection is provided. A trivial search to determine the value of the 40-bit RC2 key can recover the Triple-DES key, and then the Triple-DES key can be used to decrypt the content. Therefore, implementers must ensure that key-encryption algorithms are as strong or stronger than content-encryption algorithms. Implementers should be aware that cryptographic algorithms become weaker with time. As new cryptoanalysis techniques are developed and computing performance improves, the work factor to break a particular cryptographic algorithm will be reduced. Therefore, cryptographic algorithm implementations should be modular, allowing new algorithms to be readily inserted. That is, implementers should be prepared for the set of algorithms that must be supported to change over time. Housley Standards Track [Page 55]
RFC 5652 Cryptographic Message Syntax September 2009 The countersignature unsigned attribute includes a digital signature that is computed on the content signature value; thus, the countersigning process need not know the original signed content. This structure permits implementation efficiency advantages; however, this structure may also permit the countersigning of an inappropriate signature value. Therefore, implementations that perform countersignatures should either verify the original signature value prior to countersigning it (this verification requires processing of the original content), or implementations should perform countersigning in a context that ensures that only appropriate signature values are countersigned. 15. Acknowledgments This document is the result of contributions from many professionals. I appreciate the hard work of all members of the IETF S/MIME Working Group. I extend a special thanks to Rich Ankney, Simon Blake-Wilson, Tim Dean, Steve Dusse, Carl Ellison, Peter Gutmann, Bob Jueneman, Stephen Henson, Paul Hoffman, Scott Hollenbeck, Don Johnson, Burt Kaliski, John Linn, John Pawling, Blake Ramsdell, Francois Rousseau, Jim Schaad, Dave Solo, Paul Timmel, and Sean Turner for their efforts and support. I thank Tim Polk for his encouragement in advancing this specification along the standards maturity ladder. In addition, I thank Jan Vilhuber for the careful reading that resulted in RFC Errata 1744. Author's Address Russell Housley Vigil Security, LLC 918 Spring Knoll Drive Herndon, VA 20170 USA EMail: housley@vigilsec.com Housley Standards Track [Page 56]
mirror server hosted at Truenetwork, Russian Federation.